Z28U!

iTrader: (1)

Last year basically stock I ran 13.4 in june. With new 90mm ported fast intake, 92mm ptm tb, reduction of complete ac system and Powerbond pulley I ran 12.7 this past Wednesday. Both times we're in late June and in the 90's; driving to the track, putting slicks on and racing right away. Looking to keep drilling down and work into 11's. Every little bit counts. I've even heard alot of ppl taking front sway bar out for .10-.20 et reduction. What should be next to get into 11's.

HCI2000SS

iTrader: (2)

100 shot

redbird555

iTrader: (14)

do you headers? list of mods please

transamtom

iTrader: (8)

Exhaust like Red and HCI said.

More weight reduction,suspension and a torque converter if your auto or a good clutch and a stout rear end if your stick.

Z28U!

iTrader: (1)

Mods:
- 1 7/8 Texas speed lts with dual cutouts then dumped before axle
- fast 90 ported by vengeance racing
- ptm 92mm tb
- slp lid
- free mod cutout
- Powerbond underdrive pulley
- ssra (super sucker ram air )
- weld wheels bigs and skinnies. Hoosier slicks on back
- weight reduction ; I've taken out radio, speakers, carpet, back seat, original front seats replaced with kirkeys, Jack out, ac/egr and air deleted

Z28U!

iTrader: (1)

I forgot, I also have frost tune

scotty2000ss

iTrader: (2)

What mph are you putting up? What are your rpms at when you trap?

Z28U!

iTrader: (1)

Trapped a little over 108mph

transamtom

iTrader: (8)

So we still don't know whether its an M6 or Auto.

Do you have a stall?

Aftermarket clutch?

M6 on a stock 10 bolt really limits you a stalled auto not so much.

scotty2000ss

iTrader: (2)

That's a good time. Nice job.

Z28U!

iTrader: (1)

It's anot auto a4, no stall

AnotherWs6

iTrader: (17)

AHhhhhh, no stall. That should be your next mod.

transamtom

iTrader: (8)

Yup a quality 3600 to 4000 stall with the proper tune should get you close to 11's.

Dark SS

iTrader: (6)

An SS 3600 dropped my ET by half a second. A good stall is a must.

high n dry

iTrader: (18)

I can't agree more! I have an ss3600, just ran 12.3 @ 108 at my local track. Just have stall, S60 3.73 & SLP lid.

typedRew

All that with a stock converter, what a waste.

Get a converter in that thing and find the power you're supposed to have.

That's a high 11s in a decent DA car.

PT4000 Yank if you don't plan on putting nitrous to it, SS4000 if it's a possibility.

Edit; has that tune been touched up for all those new parts? MPH seems low, but probably just due to converter.

- Drew

Z28U!

iTrader: (1)

Yea computer was sent out and installed after all parts. Sounds like converter would get me into high 11's as mentioned. Will all my stock bottom end parts hold up after installing aftermarket stall?

typedRew

Stall won't have any affect on your bottom end, you have plenty of 'room' for more power.

- Drew

Jake89

As stated the stock bottom end is not a concern. I would be more concerned with the heat added to the transmission. Pick up a transmission cooler. I think you can find some off of Amazon for $50 or so. Also, I believe there is one being sold with a TCI torque converter in the classifieds. You might want to check that out.

typedRew

I would also step down to some ET Street Drag radials, I can almost guarantee you are losing more than you are gaining with those on the back.

Plenty of ET streets in the 1.5x 60s to warrant their use instead of slicks. I would only use slicks on a mild build M6 car, waste on an auto.

- Drew