How Do you test the coil packs ?
#2
ls1 coil packs are pretty much indestructable. i work at a gm dealership and have yet to see them fail. what codes do you have? p0300? any other codes? you likely have another issue spark/fuel related. no one can help without codes you pulled from it. give us a starting point.
#3
Teching In
Thread Starter
Join Date: May 2008
Location: N CA
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
I got it scanned and it said multipile mis fire p0300. It has stock injectors the check engine light stays on and some times will flash while driving, when i hit the accelertaor black smoke will come out?!
Trending Topics
#9
TECH Resident
iTrader: (15)
Join Date: Oct 2006
Location: Tennessee
Posts: 910
Likes: 0
Received 0 Likes
on
0 Posts
ls1 coil packs are pretty much indestructable. i work at a gm dealership and have yet to see them fail. what codes do you have? p0300? any other codes? you likely have another issue spark/fuel related. no one can help without codes you pulled from it. give us a starting point.
#12
12 Second Club
Ignition Coil Test
1. Disconnect the ignition coil output wire at the distributor cap.
2. Connect a spark plug to the end of the ignition coil output wire which you just disconnected.
3. Connect a ground wire to the threaded portion of the spark plug.
4. Disconnect the ignition coil ground wire from the negative terminal on the coil (Green Wire).
5. Connect one end of a ground wire to the ignition coil negative terminal.
6. Turn the ignition switch to the ON position.
7. Tap the other end of the ignition coil ground wire jumper on an good grounding point (for example the battery negative terminal) and look for sparks at the spark plug that correspond to the frequency of your tapping of the ground wire.
8. If you have a good spark at the spark plug, the ignition coil is good.
9. If you don't get a good spark, check for approximately 12 VDC from the coil positive terminal (black wire) to ground with the ignition switch in the ON position. You should also get approximately 12 VDC from the coil negative terminal (Green wire) to ground
Ignition Coil Resistance Check
In addition to the test above, you may elect to perform an ignition coil resistance check as confirmation of the coil's condition.
1. Check the ignition coil primary coil resistance by connecting an ohmmeter between the positive (Black wire) and negative (Green wire) terminals on the coil. The resistance should be 0.4 to 0.6 ohms.
2. Check the ignition coil secondary coil resistance by connecting an ohmmeter between the coil output terminal and the ignition coil negative terminal. The resistance should be 5000 to 7200 ohms.
1. Disconnect the ignition coil output wire at the distributor cap.
2. Connect a spark plug to the end of the ignition coil output wire which you just disconnected.
3. Connect a ground wire to the threaded portion of the spark plug.
4. Disconnect the ignition coil ground wire from the negative terminal on the coil (Green Wire).
5. Connect one end of a ground wire to the ignition coil negative terminal.
6. Turn the ignition switch to the ON position.
7. Tap the other end of the ignition coil ground wire jumper on an good grounding point (for example the battery negative terminal) and look for sparks at the spark plug that correspond to the frequency of your tapping of the ground wire.
8. If you have a good spark at the spark plug, the ignition coil is good.
9. If you don't get a good spark, check for approximately 12 VDC from the coil positive terminal (black wire) to ground with the ignition switch in the ON position. You should also get approximately 12 VDC from the coil negative terminal (Green wire) to ground
Ignition Coil Resistance Check
In addition to the test above, you may elect to perform an ignition coil resistance check as confirmation of the coil's condition.
1. Check the ignition coil primary coil resistance by connecting an ohmmeter between the positive (Black wire) and negative (Green wire) terminals on the coil. The resistance should be 0.4 to 0.6 ohms.
2. Check the ignition coil secondary coil resistance by connecting an ohmmeter between the coil output terminal and the ignition coil negative terminal. The resistance should be 5000 to 7200 ohms.
The following users liked this post:
strikeone (09-25-2022)
#14
ls1 coil packs are pretty much indestructable. i work at a gm dealership and have yet to see them fail. what codes do you have? p0300? any other codes? you likely have another issue spark/fuel related. no one can help without codes you pulled from it. give us a starting point.
I have a failed one on my lap now
My LS1 commodore started running like a bitch on 7 cyls and threw a code
P0354
Circuit open, shorted or earther for less than 15 seconds
I started the car from cold the next day and the no4 header pipe had no heat at all after 1 minute of running so its more than a miss fire.
Relpaced it and all is good
I put it down to being too close to the stainless headers after my coil relocation so i have a shield now