Always improving..Progress on the new build
I plan on using the SS hood that is on it in the first few pictures. I planned on making the removable radiator support anyways to make it easier to work on. After cutting it and lowering it made it possible to fit the lid without cutting the hood
Yes it will. We all know it's a labor of love anyway. Love the powdercoating.
I did some more work this weekend. The engine bay is painted, 24x reluctors are installedon the engine. I need to button the engine back up then im ready to set the engine/trans in.
Bay pictures:
Heres some powder coating I did over the weekend for a friends LS powered foxbody, its a dark candy red:
Little steps, but it would be awesome to hit the track at the end of May.
Bay pictures:
Heres some powder coating I did over the weekend for a friends LS powered foxbody, its a dark candy red:
Little steps, but it would be awesome to hit the track at the end of May.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo 
Thers no bracket uh oh.I filled the spot welds, the fuel line hole, the wireing holes that went over the passenger side for the 2 connectors that connect to the engine harness. The only things I left were the holes for the junction block and ground.
Here are a couple more progress pictures. Im sorrry for the crappy cell phone pictures they just dont do it and justice. As soon as its together I'll snap some good pictures with my camera.
a little more progress. Just need to finish up the 24x harness bolt up some exhaust and run the front body harness. Hopefully I'll have it running in the next few weeks
This takes so much damn time to keep it nice. If I wasn't being so picky it would be running by now.
This takes so much damn time to keep it nice. If I wasn't being so picky it would be running by now.
The car runs 10's on the bottle. I doubt it runs tens on motor this year after adding the heavier 9" and huge 35 spline axles.
I just wanted to clean things up and make it easier to work on. it would be nice to see an improvement in ET with the LID and 24x system going in (hopefully to solve old ignition problems I had) but thats a stretch.
I just wanted to clean things up and make it easier to work on. it would be nice to see an improvement in ET with the LID and 24x system going in (hopefully to solve old ignition problems I had) but thats a stretch.
Thanks
Closer yet now. A couple friends came over and helped yesterday. Adam routed and loomed most of the wiring it almost complete. Exhaust is on driveshaft in etc.
I need to run fuel lines and brake lines, finish looming wiring and install my coils and plug wires and it should be ready to start.
Closer yet now. A couple friends came over and helped yesterday. Adam routed and loomed most of the wiring it almost complete. Exhaust is on driveshaft in etc.
I need to run fuel lines and brake lines, finish looming wiring and install my coils and plug wires and it should be ready to start.