What did you do to your V today?
11-17-2013, 11:21 PM
#21
Launching!
Thread Starter
iTrader: (3)
Join Date: Dec 2010
Location: OR
Posts: 254
Likes: 0
Received 0 Likes
on
0 Posts
waaaaat! on my base I had odd lights out for long periods of time because I was lazy to remove the bumper all the time... are you sure.. the bottom inner lights?
11-18-2013, 12:50 AM
#22
Got my rebalanced driveshaft back from The Driveshaft Shop and re-installed it. (Rear mirror vibration is gone) Installed the rebuilt QA1's from Kidwell Motorsports. Cycled a liter of Dot 4 through the brakes. Installed the PA-15 Vette. I finished today, but it actually took a couple of days to finish.
Car feels good. Need to get it to the autocross next month.
Car feels good. Need to get it to the autocross next month.
11-18-2013, 12:58 AM
#23
Launching!
Thread Starter
iTrader: (3)
Join Date: Dec 2010
Location: OR
Posts: 254
Likes: 0
Received 0 Likes
on
0 Posts
nice. I was close to buying that PA-15 but instead went with the radio shack mod. and this http://www.buyijet.com/top-products/...ite-black.html
Im verry happy. I have the remote magnetize by my shifter so I just press my buttons from there.
and my ipod sits in my center console with no issue at all
but that balancing sounds very gainful.
Im verry happy. I have the remote magnetize by my shifter so I just press my buttons from there.
and my ipod sits in my center console with no issue at all
but that balancing sounds very gainful.
11-20-2013, 06:48 AM
#26
Launching!
iTrader: (2)
Join Date: May 2012
Location: PA
Posts: 265
Likes: 0
Received 0 Likes
on
0 Posts
I drove it... like any other day.
I've been playing with front and rear QA1 adjustments to get it right, since putting in the rears recently. (was QA1s fronts and FG2s rears)
I've been playing with front and rear QA1 adjustments to get it right, since putting in the rears recently. (was QA1s fronts and FG2s rears)
11-20-2013, 09:56 AM
#28
11-20-2013, 12:34 PM
#30
Launching!
iTrader: (2)
Join Date: May 2012
Location: PA
Posts: 265
Likes: 0
Received 0 Likes
on
0 Posts
http://ocshocks.com and I asked for thicker oil.
Installed with Banski upper mounts... note the mess from the blown FG2... anyone want the other one? I have a front FG2 as well from the same process of blown, buy QA1s.
Last edited by JDB; 11-20-2013 at 12:42 PM.
11-20-2013, 01:46 PM
#31
TECH Fanatic
iTrader: (8)
Join Date: Jun 2010
Location: Helendale
Posts: 1,921
Likes: 0
Received 0 Likes
on
0 Posts
Plugged in the battery tender I have for it...car just sits 95% of the time. From DD to Garage Space filler...all because of a 135 mile round trip commute for work.
11-21-2013, 10:29 PM
#33
Staging Lane
iTrader: (4)
Join Date: Nov 2006
Location: Central Illinois
Posts: 51
Likes: 0
Received 0 Likes
on
0 Posts
Finally installed my new endlinks and sway bar bushings after procrastinating it for 2 months. Ahhhhh, it's so nice driving around with no front end clunking noise!
11-21-2013, 10:42 PM
#34
TECH Resident
iTrader: (15)
Join Date: Jan 2008
Location: Memphis TN
Posts: 822
Likes: 0
Received 0 Likes
on
0 Posts
Got the car in the air to nut and bolt it after the last round of mods. Found a missing trans mount bolt missing. Fixed that need to get some gaskets for the exhaust and will get an oil change tomorrow.
Also clay bared the front bumper from the last trip up north.
Also clay bared the front bumper from the last trip up north.
11-22-2013, 02:46 AM
#35
TECH Fanatic
Had the car flash a low warning light... And yea the fluid is a bit low. She's got almost 90k miles so I figure, just do new upper and lower hoses and new radiator fluid... I'll knock it all out when I change the oil next week. Ordered up all the parts today
And yea I checked around... Didn't see any leaks real visible, its probably the original fluid and its been there for how many years and miles. But I started it up and it didn't feel like the head gasket. The cylinders weren't pressurizing the system when I grabbed the upper hose so I dunno. Only $50 worth of hose and piece of mind.
And yea I checked around... Didn't see any leaks real visible, its probably the original fluid and its been there for how many years and miles. But I started it up and it didn't feel like the head gasket. The cylinders weren't pressurizing the system when I grabbed the upper hose so I dunno. Only $50 worth of hose and piece of mind.
Last edited by ryridesmotox; 11-22-2013 at 09:45 AM.
