Bulkhead or inline connector for engine wiring harness
#1
Teching In
Thread Starter
iTrader: (1)
Join Date: Aug 2004
Posts: 17
Likes: 0
Received 0 Likes
on
0 Posts
Bulkhead or inline connector for engine wiring harness
I plan to mount the PCM inside the car under the dash. I am looking for a clean bulkhead pass through (or inline connector) to be able to split the main harness. It looks like it would need ~80-90 pins total. I could do it in a couple of connectors as there probably isn't a single one that big. Any experience or ideas are appreciated.
Thanks
Thanks
#2
TECH Fanatic
iTrader: (1)
I plan to mount the PCM inside the car under the dash. I am looking for a clean bulkhead pass through (or inline connector) to be able to split the main harness. It looks like it would need ~80-90 pins total. I could do it in a couple of connectors as there probably isn't a single one that big. Any experience or ideas are appreciated.
Thanks
Thanks
#3
TECH Senior Member
iTrader: (7)
I plan to mount the PCM inside the car under the dash. I am looking for a clean bulkhead pass through (or inline connector) to be able to split the main harness. It looks like it would need ~80-90 pins total. I could do it in a couple of connectors as there probably isn't a single one that big. Any experience or ideas are appreciated.
Thanks
Thanks
http://www.iimuchfabrication.com/electrical.html
Andrew
#5
TECH Addict
iTrader: (2)
One thing to note is either route will require a special crimp tool to make the connections properly.
#6
I uses this connector.
http://www.ebay.com/itm/22-Cavity-Weatherpack-Bulkhead-Connector-Kit-12-to-20-AWG-w-Locks-/230837733667?pt=Race_Car_Parts&hash=item35bf004923&vxp=mtr
very nice, easy to put together.
http://www.ebay.com/itm/22-Cavity-Weatherpack-Bulkhead-Connector-Kit-12-to-20-AWG-w-Locks-/230837733667?pt=Race_Car_Parts&hash=item35bf004923&vxp=mtr
very nice, easy to put together.
Trending Topics
#8
Teching In
Thread Starter
iTrader: (1)
Join Date: Aug 2004
Posts: 17
Likes: 0
Received 0 Likes
on
0 Posts
Awesome - thanks for all the responses and especially the links, guys! There are a few good options out there.
I have the crimp tools for the weatherpack and metripack (at least the 150, not sure if that is the same one for the 280/480 referenced on the 30 pin), so those are catching my attention. The Molex sure are nice and I have seen those used in vehicle applications. The Molex XRC crimp tool looks like it is $300 - yikes!
The pass through grommet is interesting (and very cost effective) as well. I never really thought about that. The packaging size on that ends up being significantly smaller. I need to do some sizing up on the space I have available.
I assume you guys end up using 3 (or 4) of the 20-31 pin connectors, right?
I have the crimp tools for the weatherpack and metripack (at least the 150, not sure if that is the same one for the 280/480 referenced on the 30 pin), so those are catching my attention. The Molex sure are nice and I have seen those used in vehicle applications. The Molex XRC crimp tool looks like it is $300 - yikes!
The pass through grommet is interesting (and very cost effective) as well. I never really thought about that. The packaging size on that ends up being significantly smaller. I need to do some sizing up on the space I have available.
I assume you guys end up using 3 (or 4) of the 20-31 pin connectors, right?
#11
Teching In
Thread Starter
iTrader: (1)
Join Date: Aug 2004
Posts: 17
Likes: 0
Received 0 Likes
on
0 Posts
I'm still doing my research, but your point is well taken...
More details for anyone following this or searching it later:
I found it at Summit for sub $30 like you said: Link to split grommet at Summit
- Available with holes from 1/4" to 1" in 1/8" increments.
- I also found that the overall outer diameter is 3".
Seals-It Website
#12
TECH Apprentice
iTrader: (6)
I used the grommet like the one above on my previous build. They work well and seal really well around your harness. In the future though I will use the bulkhead. You are correct that for the engine you will only need a few wires but I plan on running my complete front end harness through mine and hide it inside a fender well out of sight. That way if the front end ever needs to be removed it will be a simple process.
#14
At the same time I think everyone has had issues with wires chaffing on sheet metal edges and causing intermittent shorts. That kind of bug will flat drive you crazy. Obviously keeping the grommets in good shape and you have a single point of failure. But still, if you build the connector right it and do a lot or maintenance being able to disconnect the wires rather than tugging them out of the way might be the better option.
#16
TECH Junkie
iTrader: (11)
Boy, I don't know about that. I see your argument. If you were talking 1970 and older connections I wouldn't hesitate to agree. I know Chrysler used some firewall bulkhead connectors that have pretty bad reputations. But can't say I've ever had an issue with EFI connectors. The sealed metric pack stuff is massively reliable and the Molex stuff is expensive for a reason.
At the same time I think everyone has had issues with wires chaffing on sheet metal edges and causing intermittent shorts. That kind of bug will flat drive you crazy. Obviously keeping the grommets in good shape and you have a single point of failure. But still, if you build the connector right it and do a lot or maintenance being able to disconnect the wires rather than tugging them out of the way might be the better option.
At the same time I think everyone has had issues with wires chaffing on sheet metal edges and causing intermittent shorts. That kind of bug will flat drive you crazy. Obviously keeping the grommets in good shape and you have a single point of failure. But still, if you build the connector right it and do a lot or maintenance being able to disconnect the wires rather than tugging them out of the way might be the better option.
I'm talking (the integrity of) factory connections vs. home-built. You never know what you're gonna get when home builders do connectors. For instance, I always solder all of my electrical connections and thought that was the best way until reading posts by PSI harnesses. Now I may re-think my methodology...
#17
I am planing to try these ****IF**** I ever get my swap running.
#19
Teching In
Thread Starter
iTrader: (1)
Join Date: Aug 2004
Posts: 17
Likes: 0
Received 0 Likes
on
0 Posts
Those of you that are using the Molex connectors (like the Molex XRC), what are you using for crimp tools? I can't find anything less than $300. But, I have found multiple places, including the link above, that says you can use standard crimp tools. To me a standard crimp tool is not $300, so they must know something I don't know...
#20
TECH Apprentice
We are just finishing up a project car that I used the Ampseal 35 pin headers, and connectors on.
Just like those but in the 35 pin version.
Here is a quick video I did of the wiring project so far.
Just like those but in the 35 pin version.
Here is a quick video I did of the wiring project so far.