almost done with my nitrous 408
#1
10 Second Club
Thread Starter
iTrader: (1)
Join Date: Mar 2005
Location: Lake Hopatcong
Posts: 147
Likes: 0
Received 0 Likes
on
0 Posts
almost done with my nitrous 408
like the title says i've got most of my parts in for my n2o 408 engine its gonna be going into my 99 frc vette just wanted to see wat u guys though of my progress so far and if you had any thoughts... well here is the list so far....................
so far..
6.0l iron block
partiot perf. stage 3 ls6 heads
JE pistons 4.030 10.5 comp ratio. bigger rings for nitrous and custom dish
Eagle h beam rods 6.125 with upgraded rod bolts for n2o
4.0" eagle crank forged
next to order...
harland sharp roller rockers
thunder racing custom cam 244/248, 509/605 113 lsa (might go bigger not sure yet)
lg long tubes
and direct port kit 250-300 shot
im lookin for 600-650hp na crank and 900-1000 juice
any comments are welcome
so far..
6.0l iron block
partiot perf. stage 3 ls6 heads
JE pistons 4.030 10.5 comp ratio. bigger rings for nitrous and custom dish
Eagle h beam rods 6.125 with upgraded rod bolts for n2o
4.0" eagle crank forged
next to order...
harland sharp roller rockers
thunder racing custom cam 244/248, 509/605 113 lsa (might go bigger not sure yet)
lg long tubes
and direct port kit 250-300 shot
im lookin for 600-650hp na crank and 900-1000 juice
any comments are welcome
#7
10 Second Club
Thread Starter
iTrader: (1)
Join Date: Mar 2005
Location: Lake Hopatcong
Posts: 147
Likes: 0
Received 0 Likes
on
0 Posts
well im gonna switch to 4.10's in the rear and upgrade the output shafts the trans im gonna see how much power these t-56's can take hahah....
im gonna switch to coil-overs most likley and see wat happens i think i might start building a trans after the engine gets done hahah
my old set up i had 100-shot, bf drag radials 295, k&n intake, colder plugs, and bassani cat-back, that got me a best of 12.1 at 117 with a 1.805 60ft.
im gonna switch to coil-overs most likley and see wat happens i think i might start building a trans after the engine gets done hahah
my old set up i had 100-shot, bf drag radials 295, k&n intake, colder plugs, and bassani cat-back, that got me a best of 12.1 at 117 with a 1.805 60ft.
Last edited by n2oJOE; 10-29-2005 at 04:53 PM.
Trending Topics
#11
10 Second Club
Thread Starter
iTrader: (1)
Join Date: Mar 2005
Location: Lake Hopatcong
Posts: 147
Likes: 0
Received 0 Likes
on
0 Posts
i have a single fogger system already im just gonna upgrade to direct port.
yea the big ? is wat clutch i should run its gonna be drivin on the street everynow and then lol but put some serious power down so im not sure yet wat to run
yea the big ? is wat clutch i should run its gonna be drivin on the street everynow and then lol but put some serious power down so im not sure yet wat to run
#14
10 Second Club
Thread Starter
iTrader: (1)
Join Date: Mar 2005
Location: Lake Hopatcong
Posts: 147
Likes: 0
Received 0 Likes
on
0 Posts
yea we will have to get every one together at the mall some time i wanna check out that quick little poopra u got and everyone should have there cars back this year kris talons almost done cj did a 9in' and 150 shot and think hes doing a cam over the winter too so there gonna be some fast cars around the bury come spring time