LS1TECH - Camaro and Firebird Forum Discussion

Dynamometer Results & Comparisons Dyno Records | Dyno Discussion | Dyno Wars

Dyno guesses???

Thread Tools
 
Search this Thread
 
Old 06-28-2008, 03:09 PM
  #1  
Launching!
Thread Starter
iTrader: (7)
 
toneloc60's Avatar
 
Join Date: Mar 2005
Posts: 291
Likes: 0
Received 1 Like on 1 Post

Default Dyno guesses???
Monday is the big day. My engine should finally get on the dyno. What do you think it'll make at the flywheel? It's built for nitrous, but will be N/A Monday.

LSX 441ci 11:1 cr
6.125" Lunati Pro Billet Rods
4.125" Compstar Callies crank
4.125" custom Wiseco pistons for nitrous
Meziere street version w/p
LS7 heads ported and polished with Ti and sodium filled valves
LS7 carb intake
950 Quick Fuel Technologies carb modified for E85
MSD coils and wires
Harland Sharp custom made roller tip rockers (still 1.8:1)
Melling high pressure and high volume oil pump
Kook's 2" primary headers w/LS7 flange and 3 1/2 collectors
MSD ingnition controller for LS2
Cloyes double roller timing set
Custom Comp Cam: (Everything is based on 1.7:1 rockers, I have 1.8:1)
Gross valve lift Intake .623 Exhaust .623
Duration Intake 254 Exhaust 266
112 Intake center line
114 lobe separation

I should've been on the dyno Friday, but had the wrong crank sensor. I have my fingers crossed for everything to be right Monday.
toneloc60 is offline  
Reply Like
Old 07-03-2008, 12:56 AM
  #2  
Launching!
Thread Starter
iTrader: (7)
 
toneloc60's Avatar
 
Join Date: Mar 2005
Posts: 291
Likes: 0
Received 1 Like on 1 Post

Default
Here are the numbers. Sorry, the graph isn't scanning in very well. Yes, these #'s are at the flywheel.
Attached Thumbnails Dyno guesses???-dyno-sheet003.jpg  
Last edited by toneloc60; 07-03-2008 at 01:10 AM.
toneloc60 is offline  
Reply Like
Old 07-03-2008, 02:19 AM
  #3  
12 Second Club
iTrader: (5)
 
krazy4's Avatar
 
Join Date: Mar 2006
Location: Yorba Linda, CA
Posts: 1,457
Likes: 0
Received 3 Likes on 3 Posts

Default
Nice numbers man!
krazy4 is offline  
Reply Like
Old 07-03-2008, 02:34 AM
  #4  
Launching!
Thread Starter
iTrader: (7)
 
toneloc60's Avatar
 
Join Date: Mar 2005
Posts: 291
Likes: 0
Received 1 Like on 1 Post

Default
Thanks.
toneloc60 is offline  
Reply Like
Old 07-03-2008, 06:50 PM
  #5  
TECH Senior Member
iTrader: (2)
 
gator's 99TA's Avatar
 
Join Date: Nov 2001
Location: Tampa Bay
Posts: 9,971
Likes: 0
Received 2 Likes on 2 Posts

Default
very impressive!
gator's 99TA is offline  
Reply Like
Old 07-03-2008, 08:38 PM
  #6  
11 Second Club
iTrader: (17)
 
bad6as's Avatar
 
Join Date: Mar 2005
Location: Maryland
Posts: 4,796
Likes: 0
Received 0 Likes on 0 Posts

Default
743hp 634tq
dam....
bad6as is offline  
Reply Like
Old 07-03-2008, 10:25 PM
  #7  
11 Second Club
 
347fairless's Avatar
 
Join Date: Oct 2005
Location: Philly
Posts: 323
Likes: 0
Received 0 Likes on 0 Posts

Default
Sweet numbers man.

What is with the A\F?
347fairless is offline  
Reply Like

Trending Topics

Old 07-03-2008, 10:28 PM
  #8  
Launching!
Thread Starter
iTrader: (7)
 
toneloc60's Avatar
 
Join Date: Mar 2005
Posts: 291
Likes: 0
Received 1 Like on 1 Post

Default
Originally Posted by 347fairless
Sweet numbers man.

What is with the A\F?

Thanks. I'm running on E85. I kept the compression low enough for pump gas, but am choosing to run E85 for the higher octane at lower cost. It'll be needed once I get the N20 hooked up.
toneloc60 is offline  
Reply Like
Old 07-03-2008, 10:52 PM
  #9  
TECH Junkie
iTrader: (14)
 
MYSTIC-1SC's Avatar
 
Join Date: Sep 2007
Posts: 3,278
Likes: 0
Received 14 Likes on 5 Posts

Default
impressive
MYSTIC-1SC is offline  
Reply Like
Old 07-05-2008, 11:21 AM
  #10  
9 Second Club
iTrader: (33)
 
ramairws6's Avatar
 
Join Date: Sep 2004
Location: Hicksville MN!
Posts: 1,990
Likes: 0
Received 83 Likes on 59 Posts

Default
Sweet dude!!
ramairws6 is offline  
Reply Like
Old 07-06-2008, 05:27 PM
  #11  
8 Second Club
iTrader: (41)
 
Firehawk441's Avatar
 
Join Date: May 2005
Posts: 2,119
Likes: 0
Received 12 Likes on 9 Posts

Default
Looks like solid #'s. Those big heads love cubic inches. Good luck with it.
Firehawk441 is offline  
Reply Like
Old 07-06-2008, 08:41 PM
  #12  
TECH Junkie
iTrader: (4)
 
Gordon0652's Avatar
 
Join Date: Sep 2006
Posts: 3,188
Received 2 Likes on 2 Posts

Default
Great numbers!
Looks like that engine is running a little rich from the dyno sheet?
Gordon0652 is offline  
Reply Like
Old 07-06-2008, 09:49 PM
  #13  
Launching!
Thread Starter
iTrader: (7)
 
toneloc60's Avatar
 
Join Date: Mar 2005
Posts: 291
Likes: 0
Received 1 Like on 1 Post

Default
Nope, it's running E85.
toneloc60 is offline  
Reply Like
Old 07-07-2008, 12:05 AM
  #14  
TECH Junkie
iTrader: (4)
 
Gordon0652's Avatar
 
Join Date: Sep 2006
Posts: 3,188
Received 2 Likes on 2 Posts

Default
Bad *** then!
Gordon0652 is offline  
Reply Like
Old 07-08-2008, 11:33 PM
  #15  
11 Second Club
iTrader: (15)
 
Fifedogg's Avatar
 
Join Date: Mar 2007
Location: So Cal
Posts: 772
Likes: 0
Received 0 Likes on 0 Posts
Default
That thing is gonna be a beast!
Fifedogg is offline  
Reply Like
Old 07-15-2008, 10:47 PM
  #16  
TECH Junkie
iTrader: (10)
 
GrannySShifting's Avatar
 
Join Date: Nov 2001
Location: Glen Burnie, Md
Posts: 3,944
Received 20 Likes on 13 Posts

Default
Looks pretty healthy, shoudl be able to see some 9s even in a heavy car
GrannySShifting is offline  
Reply Like
Old 07-17-2008, 10:16 PM
  #17  
TECH Addict
iTrader: (1)
 
beardWS6's Avatar
 
Join Date: Aug 2002
Location: Lake Jackson,TX
Posts: 2,879
Likes: 0
Received 0 Likes on 0 Posts

Default
SWEET numbers man. That is going to fly!!
beardWS6 is offline  
Reply Like
Old 07-20-2008, 01:22 PM
  #18  
TECH Fanatic
iTrader: (3)
 
PONTIAC SLP's Avatar
 
Join Date: Mar 2007
Location: Middle east , Kuwait
Posts: 1,591
Likes: 0
Received 0 Likes on 0 Posts

Default
kill me man with those killing numbers !! beaaaaast
PONTIAC SLP is offline  
Reply Like
Old 07-28-2008, 02:54 PM
  #19  
Launching!
Thread Starter
iTrader: (7)
 
toneloc60's Avatar
 
Join Date: Mar 2005
Posts: 291
Likes: 0
Received 1 Like on 1 Post

Default
So, I blew the engine in my DD yesterday. Do you have any idea how tempting it is to have this engine sitting in the corner eye balling me?
toneloc60 is offline  
Reply Like
Back to Subforum
Dynamometer Results & Comparisons
View Next Unread
Help!! Something's Wrong!!




Advanced Search
Quick Reply: Dyno guesses???


Reply Closed Thread Share

All times are GMT -5. The time now is 10:32 PM.