411hp/400tq on a Mustang Dyno, Abs Spd Stg II / TPS 231/237.
09-03-2003, 08:10 PM
#1
TECH Resident
Thread Starter
iTrader: (1)
Join Date: May 2002
Location: The Thin Air
Posts: 859
Likes: 0
Received 0 Likes
on
0 Posts
411hp/400tq on a Mustang Dyno, Abs Spd Stg II / TPS 231/237. Added 3 of timing all around, didnt add any HP... acutally lost a bit of TQ, but my powerband starts earliers and finishes later now. It also made my AF Flatter which was pretty nice... 
was jumping around from 13.2 - 13.7 but now its 13.4~ pretty flat. Ill get some dyno graph pics up laters.
97degrees in the shop/29.~ baro
was jumping around from 13.2 - 13.7 but now its 13.4~ pretty flat. Ill get some dyno graph pics up laters.97degrees in the shop/29.~ baro
09-03-2003, 09:29 PM
#5
TECH Fanatic
iTrader: (6)
Join Date: Nov 2001
Location: Las Vegas
Posts: 1,101
Likes: 0
Received 0 Likes
on
0 Posts
Re: 411hp/400tq on a Mustang Dyno, Abs Spd Stg II / TPS 231/237. oh i remeber your car, you had alot of problems with it. try to post up that dyno sheet asap, did you take that pos spintech muffler off yet? loose the cats? is the graph still flatlining at the top of the rpm band.
hopefully you got it all together
hopefully you got it all together
09-03-2003, 09:38 PM
#6
Re: 411hp/400tq on a Mustang Dyno, Abs Spd Stg II / TPS 231/237. You added 3*'s??? Can't believe you didn't have clearence problems. I was advised not to advance with this cam. You should be a little over 450 on a dyno jet. Sounds like your right in line with what you are supposed to be making. Hope mine gets here soon. :p
09-03-2003, 09:44 PM
#7
TECH Resident
Thread Starter
iTrader: (1)
Join Date: May 2002
Location: The Thin Air
Posts: 859
Likes: 0
Received 0 Likes
on
0 Posts
Re: 411hp/400tq on a Mustang Dyno, Abs Spd Stg II / TPS 231/237. they were 5.7l heads, milled .030 and I have valve reliefs... i dont know if its corrected or not to be honest. Doesnt say anywhere on this dyno sheet. Just relaying the weather reading on the computer screen for the mustang dyno program.
Everything was the same as my last run on the dyno jet Mike. Still through the mufflex no cats. 27lb psi tires. M6. Was just seeing if this dyno closer to my house was reading the same as the dyno jet 1.5hrs away... looks to be the same to me. Except ATAP was reading 68xx rpms and this graph shows 64xx at the end of the run
Got an E- WP to throw on was just getting a base line before I did some changes. Also changing the mufflex to a Hooker Catback. See what changes I get. doing it all in steps.
Everything was the same as my last run on the dyno jet Mike. Still through the mufflex no cats. 27lb psi tires. M6. Was just seeing if this dyno closer to my house was reading the same as the dyno jet 1.5hrs away... looks to be the same to me. Except ATAP was reading 68xx rpms and this graph shows 64xx at the end of the run
Got an E- WP to throw on was just getting a base line before I did some changes. Also changing the mufflex to a Hooker Catback. See what changes I get. doing it all in steps.
Trending Topics
09-04-2003, 05:43 PM
#10
10 Second Club
iTrader: (5)
Join Date: Nov 2001
Location: Cali/Bay Area
Posts: 3,412
Likes: 0
Received 0 Likes
on
0 Posts
Re: 411hp/400tq on a Mustang Dyno, Abs Spd Stg II / TPS 231/237. J, Congrats on the nice numbers buddy, you fix the loose rocker? You know you could just add a cut out and keep the Spintech to see if you really lose much before you swap out...
Dan
Dan
09-04-2003, 07:04 PM
#11
TECH Apprentice
Join Date: Jul 2003
Location: bronx ny
Posts: 316
Likes: 0
Received 0 Likes
on
0 Posts
Re: 411hp/400tq on a Mustang Dyno, Abs Spd Stg II / TPS 231/237. mustang dyno is 5% lower than a dyno jet, i would say you would have pulled 435 on the dyno jet
Add the cut out
Add the cut out
09-04-2003, 07:10 PM
#12
TECH Fanatic
Join Date: Oct 2002
Location: nor cal (ripon)
Posts: 1,255
Likes: 0
Received 0 Likes
on
0 Posts
Re: 411hp/400tq on a Mustang Dyno, Abs Spd Stg II / TPS 231/237.
mustang dyno is 5% lower than a dyno jet, i would say you would have pulled 435 on the dyno jet
Add the cut out
Add the cut out
09-04-2003, 07:34 PM
#13
TECH Fanatic
Join Date: Oct 2002
Location: nor cal (ripon)
Posts: 1,255
Likes: 0
Received 0 Likes
on
0 Posts
Re: 411hp/400tq on a Mustang Dyno, Abs Spd Stg II / TPS 231/237. i just talked to him...that dyno has been tuned to put out dynojet #'s...its still not running right yet...oil compression issues, etc..
09-04-2003, 08:13 PM
#15
TECH Addict
Re: 411hp/400tq on a Mustang Dyno, Abs Spd Stg II / TPS 231/237.
You added 3*'s??? Can't believe you didn't have clearence problems. I was advised not to advance with this cam. You should be a little over 450 on a dyno jet. Sounds like your right in line with what you are supposed to be making. Hope mine gets here soon. :p
