New best 60' today.
10-14-2007, 07:54 PM
#1
8 second mod
Thread Starter
iTrader: (37)
Join Date: Nov 2002
Location: East Side Performance! mASShole
Posts: 17,879
Likes: 0
Received 0 Likes
on
0 Posts
New best 60' today. went racing today, first run on motor went 9.9 @ 136
then put the spray to it. ended up with a 1.27 60' (personal best for me, no limiter straps or bars, but ended up with this.
then put the spray to it. ended up with a 1.27 60' (personal best for me, no limiter straps or bars, but ended up with this.
10-14-2007, 08:11 PM
#3
8 second mod
Thread Starter
iTrader: (37)
Join Date: Nov 2002
Location: East Side Performance! mASShole
Posts: 17,879
Likes: 0
Received 0 Likes
on
0 Posts
haha, mental note make more money so i could have bought new heads. lol
it took nothing but the gasket. everything else is fine.
it cracked in 2 spots this time either was what i welded..
it took nothing but the gasket. everything else is fine.
it cracked in 2 spots this time either was what i welded..
10-14-2007, 08:14 PM
#4
With the way that looks in the photo it's hard to see, but I assume that happened when it was running yes? I could just see fuel/coolant/etc.etc. spraying all over the place making for a big mess.
Lucky it didn't take anything else with it, because that could have been alot worse.
Scrap alum, it's geting good $ these days, apparently you have a couple chunks that are about 40 lbs a piece or so LOL.
Lucky it didn't take anything else with it, because that could have been alot worse.
Scrap alum, it's geting good $ these days, apparently you have a couple chunks that are about 40 lbs a piece or so LOL.
10-14-2007, 08:16 PM
#5
8 second mod
Thread Starter
iTrader: (37)
Join Date: Nov 2002
Location: East Side Performance! mASShole
Posts: 17,879
Likes: 0
Received 0 Likes
on
0 Posts
yes it was running, but it just sprayed a little water around, but i run water only so it cleaned right up.
yea im going to pull the springs and the valves and junk the heads.
yea im going to pull the springs and the valves and junk the heads.
Trending Topics
10-14-2007, 08:42 PM
#10
8 second mod
Thread Starter
iTrader: (37)
Join Date: Nov 2002
Location: East Side Performance! mASShole
Posts: 17,879
Likes: 0
Received 0 Likes
on
0 Posts
know whats funny, ive been home for a couple hours and im already unloaded, car is apart, i ate dinner and im 5 beers deep. lol
10-14-2007, 08:48 PM
#14
8 second mod
Thread Starter
iTrader: (37)
Join Date: Nov 2002
Location: East Side Performance! mASShole
Posts: 17,879
Likes: 0
Received 0 Likes
on
0 Posts
heres todays pic. it was about a 50 foot power wheelie, car was working. i made a few adjustment this week and it worked!
10-14-2007, 10:03 PM
#20
11 Second Club
iTrader: (1)
Join Date: May 2005
Location: Sutton, MA
Posts: 242
Likes: 0
Received 0 Likes
on
0 Posts
Hey Brad, i dont know if i met ya or not but your guys let me borrow a jack so i could put my et streets on. I finally got to see your car in person too unfortunatley it was right after the heads cracked and it was already parked. Good luck with it and thanks again!
Anthony
Anthony