slowlsx

iTrader: (28)

5/8 Studs installed


TRZ Upper/Lowers installed, just need to drop the temporary Strange Dbl adjustables in until my foodstamps come in and i can exchange them for cash and get some Mencers

slowlsx

iTrader: (28)

Racewire solutions will be doing the wiring on the car and will be converting my holley wiring harness to Mil Spec bulk head connectors on the firewall and i will also be using their awesome wiring board and custom switch panel with led dome light!







Some of the guys work, looks amazing.

https://www.facebook.com/media/set/?...1086782&type=3

Blown06

iTrader: (32)

Out of curiosity.....you've mentioned "chassis shop" in several posts but I never saw who it was doing the work..........what chassis shop are you referring to?

Good choice on the wiring. **** is amazing.

slowlsx

iTrader: (28)

Rick Stevens out of Santana Fe, TX. Great work and reasonable. I need to get it back over there for a few things hopefully he can make some room for me in a few weeks

TurboTerry87gn

Thats a sweet car. Lots of good parts thrown at it too. I cant wait to see what numbers you run. Lots of good info on the thread, Thanks.

TurboTerry87gn

I would like to know how much the Mencers set you back. I hear alot about him in the drag radial world.

slowlsx

iTrader: (28)

I actually went with strange DBL adjustable in the mean time. I went maybe 4x over my budget so I just went with these until I see that I am being held back by them. Mencers are about 1600 for a pair if I remember correctly. I would see myself upgrading the rear first when the time comes. 3200 is a whole lot of cash to spend on shocks.

LS1PUNK

iTrader: (5)

Nice choice on the racewire.

Will you be shipping the car to him or installing everything yourself?

I REALLY would like to check the car out after its wired.

slowlsx

iTrader: (28)

I am sending him the holley kit and all of the harnesses. He will be building a wiring board on a carbon sheet, converting the holley harness to mil spec connectors so I can disconnect it straight from the firewall, and a pre made harness for the fuel pump/fans/Air to water pump and all the other miscellaneous things that I will be running. The switch panel also has a harness with a mil spec connector that will go straight to the wiring board so it should be a simple install on my end.

LS1PUNK

iTrader: (5)

O ok, I was going to send Brian my car awhile back but some things came up and prevented me from doing so.

Can you PM what its going to cost to do everything mentioned above?

slowlsx

iTrader: (28)

He is running a 10% discount this month so I got to take advantage of that ($200+) I'll pm you

slowlsx

iTrader: (28)

Got all of my Holley parts which I have been waiting forever for! I will be shipping everything to race wire solutions Monday morning!

herecomesboost

Cool project!

Blown06

iTrader: (32)

Your gonna out grow that hp on a turbo set up in the first 60'.

slowlsx

iTrader: (28)

I didn't see the need for the dominator although I should have anyway. I can't use a traction control device, I don't need to control nitrous, meth, tranny etc. All I really need is the D/S sensor

slowlsx

iTrader: (28)

If anything I'll just use yours

a98ws6

iTrader: (48)

Im interested in how it does with the HP. Im in the same boat as you.

slowlsx

iTrader: (28)

The hp is not any more or less better than the dominator. .. it just has more outputs. I looked at everything I was gonna use and it fit with the HP, if I were using meth, traction control and nitrous to spool then I would need the dominator but you don't need all that **** to run 4.60's

a98ws6

iTrader: (48)

I might be using meth buth none of the other stuff.

asubennett

iTrader: (6)

The milspec Holley harness on his facebook is mine. His work is flawless. He even integtated the Holley IO harness without me asking. Could not be happier with his work even if he is way way too busy these days. I dont think the dude sleeps.