Fob Programming - LS1TECH

Go Back   LS1TECH > WELCOME TO LS1TECH > General LSX Automobile Discussion
Log In 

General LSX Automobile Discussion
Non-technical LSX related topics.
Sponsored by
Stainless Headers
Click Here

Fob Programming

Thread Tools Search this Thread
Old 05-30-2009, 06:48 PM   #1
TECH Enthusiast
RikkiTorment's Avatar
Join Date: Mar 2009
Location: West Chester, PA
Posts: 511
Send a message via AIM to RikkiTorment
Default Fob Programming

Does anybody have the instructions to program a 2000 Camaro? My car came with a remote programmed for a different car and I don't want the alarm to keep going off everytime I enter with the key.
RikkiTorment is offline   Reply With Quote
Old 05-30-2009, 06:58 PM   #2
Formerly darynC-10/23/10
iTrader: ( 19 )
Daryn's Avatar
Join Date: Aug 2006
Location: gonzales louisiana
Posts: 2,301
Send a message via AIM to Daryn

1. Turn ignition off. Remove RADIO (fuse No.17) from fuse block. Cycle ignition switch from OFF to RUN positions 3 times within 5 seconds until door locks and hatch release cycles, indicating Body Control Module (BCM) is in programming mode. Leave ignition switch in RUN position.

2. Press both LOCK and UNLOCK buttons on remote control door lock transmitter for 16seoncds. Door locks will cycle once, confirming transmitter code is programmed. Door locks must cycle completely to unlock before proceeding. Any transmitter code that was previously programmed has been erased. BCM is now programmed to remote control door lock transmitter.

3. When programming BCM to match remote control door lock transmitters, first transmitters code matched will be stored in memory unless a second remote control door lock transmitter is matched at the same time. If programming BCM to match a second remote control door lock transmitter, repeat step 2). This must be done before RADIO (fuse No. 17) is reinstalled. Turn ignition off. Reinstall RADIO (fuse No. 17) to fuse block.
2012 CCSB DENALI-upper middle-class sleeper
Daryn is offline   Reply With Quote
Old 05-30-2009, 07:00 PM   #3
TECH Resident
iTrader: ( 10 )
philsblwnz28's Avatar
Join Date: Feb 2008
Location: Kissimmee
Posts: 921

pull radio fuse
cycle key on/off 3 times
trunk should open
hold lock and unlock button on your fob for 20 sec
98' Z28 LS1
LS6 Intake, Stock Cam, Stock "853's", Stock Internals, Stock Pulley, SLP Lid, Chrs1313 Ram Air, Pacesetter LT's, 3" Y-pipe, SS4000 Yank, 3.73 posi 10 bolt, M/T DR's.........2800lbs

88 Gmc Sierra 5.7-DD
philsblwnz28 is offline   Reply With Quote
Old 07-28-2009, 11:13 PM   #4
Teching In
Join Date: Jun 2009
Posts: 27

what about like the hatch buttons
djkeene16 is offline   Reply With Quote
Old 07-28-2009, 11:21 PM   #5
iTrader: ( 3 )
Join Date: Jan 2007
Location: New Braunfels/Mission, TX
Posts: 276

Same process.

I bought a new key fob since my car didnt have it. Did the steps mentioned above. Everything worked. lock/unlock/open hatch/panic
1999 Pewter Trans Am - A4 3.23s, MTI clear lid, Pacesetter LTs, ORY, Hooker Aerochamber, Tune by 1BAD_LS1
Pitbull329 is offline   Reply With Quote

2012, bcm, camaro, programming

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are Off


All times are GMT -5. The time now is 12:56 AM.