02ws666

iTrader: (1)

I was just wondering what average to good 60 foot times are in an M6 no suspension mods and just the mods in my sig.

Best i have ran is a 2.007.... just wanted to know how that stacks up and if i am descent or if i have some work to do...

RARON455

iTrader: (35)

I have a ford nine inch, with BMR LCAs and Panhard,QA1s, Welded in subframe connectors, strange coilovers on the front and et streets on the car and on the motor (bolt-ons) I cut 1.90s on a 120 shot its been in the 1.7s I still am working on dialing this stupid thing in though I believe the problem is me, I just recently found out that I should have been doing my burnouts in 2nd or 3rd gear. I have always raced autos...
Thats with me leaving from 5k on the 2step.

So considering that your car has no suspension mods I would say that sounds about right.

NSSANE02

iTrader: (14)

With drag radials, you have some room to improve but it's not horrible. In my last car I averaged a 1.9 with only nitto dr's and a borla catback. This car though, with the 9", gears, ET Streets, and suspension comes off the line like a rocket (for a little bolt-on car)

ndfrsd6

iTrader: (5)

with very little suspension i was going low 1.6's on a et street bias ply ....got suspension sorted out and went a best of 1.49 60ft on a et drag radial ...it takes a lot of seat time to get a M6 to work

AChotrod

iTrader: (17)

Im stuck in the high 1.8s and its pissing me off. Time for some relocation brackets & drag shocks & springs.

ndfrsd6

iTrader: (5)

that will defiantly help Mike ....and i would also say it may be time for 28's and a stiff wall et drag tire

AChotrod

iTrader: (17)

yep Im thinking that will help also, had to run DRs at the shootout. They will also look better! !!

Super Speed

iTrader: (8)

In my car with Bone STOCK suspension I was able to pull a 1.9 with Nittos, I wan't to get a rear so I can see what mickey's can do

02ws666

iTrader: (1)

ya with nittos my buddy pulled a 1.93. best i have gotten is a 2.007. but im also just bolt ons... i dont want to go back cuz im scared of the 10 bolt

AChotrod

iTrader: (17)

I ran 1.9s stock on my nittos also.

blu byu EH

iTrader: (25)

I'm running 1.8's with lca leaving of the two step at 4,5oo w/28x11.5x16

GG01SS

iTrader: (1)

My best is 1.89 w/ nittos, and many low 1.9's w/ stock clutch..

slowandrichws6

iTrader: (2)

i was bone stock suspention with 4.10s and 315 nittos and track bite and i was cutting 1.7's every time after i got the hang of slippin the clutch right. now my 10 bolt blew up so im in finishin up my 9 in. and it should get interesting leaving on a 200 shot and et streets

NSSANE02

iTrader: (14)

I had one launch on a 150 shot and 275 ET Streets...The clutch didn't like it much but it was definately fun

key4

iTrader: (10)

I am bolt on's too and the best I have cut is a 1.91 with the 3:42 gear, stock suspension and that was with 17" MT drag radials. I hope to get lower than that with a 4:10. I have the monster stage 3 clutch and its pretty aggresive so learning how to slip it has been a challenge to me

98blueSScamaro

iTrader: (14)

M6 is a dart game and i am getting better at it 1.64 and i am moving to a big boy tire and gear To bad some auto guys are pulling 1.40's or 1.3x's with stockgears and 10bolts

AChotrod

iTrader: (17)

I know!! We cant beat them!!!! I met a guy that went 1.3 last week in a LTx M6.
Its Tanner 2nd fastest M6 ever

Super Speed

iTrader: (8)

it really does suck...I'll eventually drop the 3k+ hang with them though

98blueSScamaro

iTrader: (14)

yea we really need to get your 60 down so me and you will clean house at rsd if you ever need help hit me up and i maybe going to 66 with you and tom tomar

Rob

SuperSlow02

iTrader: (16)

1.93 bone stock with an air lid on a falken street tire. 1.60 with a 9" and torque arm on a 28in M/T with 150 shot off the line. This time around ive got full suspension, 2 step and im stepping up to a stiff wall ET Drag...hoping for 1.4s.