Nitrous Oxide Installation | Tuning | Products
Sponsored by:
Sponsored by:

10.38 @ 135.95 on stock bottom end (video)

Thread Tools
 
Search this Thread
 
Old 01-24-2010, 05:57 PM
  #1  
10 Second Club
Thread Starter
iTrader: (1)
 
jdaniel's Avatar
 
Join Date: Dec 2004
Posts: 359
Likes: 0
Received 2 Likes on 2 Posts
Default 10.38 @ 135.95 on stock bottom end (video)

Well I finally got out to San Antonio Raceway to test out the new two step before I leave to head overseas next week and I dont even know where to begin!

Full bolt on, H/C/I/E, 4.10's, 150 shot (no controller).

First pass:

Didnt get a good burnout and the launch was really messed up. But it was the first time using the two step so I was a little nervous. I ran a 10.6 @ 133. Got to the end of the track and expected some guy to tell me to back it down. But nope... just a girl handing out time slips smiled and handed me my slip.

Got to the pits and took the bottle out to warm it back up (got a bottle heater just never got around to installing it). Some guy come up to the car looking into the windows. I asked whats up and he told me to tell the owner of the car that if I make another pass like that then I will be kicked off the property.

To make a long story short... I made a few 1/8 pulls to get the launch down. When everyone decided it was time to go I made one more pass and here is the results!!!

1/8 pull. 1.49 sixty @ 105 mph.

http://www.youtube.com/watch?v=l0bwSfoAXlk

1/4 pull. 1.46 sixty @ 135.95

http://www.youtube.com/watch?v=ki_1E5adL88

10.38 @ 135.95



Check out that short time!!! I ABSOLUTLY LOVE my Lingenfelter two step!!! HAHA!!

Last edited by jdaniel; 01-24-2010 at 06:09 PM.
Old 01-24-2010, 06:26 PM
  #2  
9 Second Club/Nitrous Mod
iTrader: (1)
 
shortdog's Avatar
 
Join Date: Nov 2003
Location: St. Louis, MO
Posts: 833
Received 0 Likes on 0 Posts


Default

Nice runs, but your car was backfiring and/or detonating like crazy from looking at the vids. I hope you checked your plugs!
Old 01-24-2010, 06:29 PM
  #3  
10 Second Club
Thread Starter
iTrader: (1)
 
jdaniel's Avatar
 
Join Date: Dec 2004
Posts: 359
Likes: 0
Received 2 Likes on 2 Posts
Default

The back firing is from the 2 step. Its a Lingenfelter LNC003. It has an upper RPM setting so when I shift I never have to come off the gas. The two step cuts ignition for a split second when I hit the clutch so a little fuel builds up in the exhaust and ignites after the shift.
Old 01-24-2010, 06:35 PM
  #4  
9 Second Club
iTrader: (21)
 
camscam02's Avatar
 
Join Date: Apr 2006
Location: sacramento, CA
Posts: 3,240
Likes: 0
Received 1 Like on 1 Post
Default

Nice work. Runs pretty hard!
Old 01-24-2010, 06:38 PM
  #5  
11 Second Club
iTrader: (16)
 
SuperSlow02's Avatar
 
Join Date: Feb 2006
Location: Cape Girardeau, MO
Posts: 1,865
Likes: 0
Received 0 Likes on 0 Posts
Default

good runs man!
Old 01-24-2010, 07:39 PM
  #6  
On The Tree
iTrader: (2)
 
daschra79's Avatar
 
Join Date: Nov 2009
Location: St. Louis area
Posts: 158
Likes: 0
Received 0 Likes on 0 Posts
Default

That's some screaming MPH. Nice runs
Old 01-24-2010, 09:25 PM
  #7  
10 Second Club
iTrader: (25)
 
blu byu EH's Avatar
 
Join Date: Aug 2007
Location: STL
Posts: 728
Likes: 0
Received 0 Likes on 0 Posts

Default

Hell Yeah six speed FTMFW!
Old 01-24-2010, 11:09 PM
  #8  
TECH Veteran
iTrader: (246)
 
robsquikz28's Avatar
 
Join Date: Mar 2008
Location: Chicago/Crown point
Posts: 4,987
Received 0 Likes on 0 Posts

Default

hell yea
Old 01-25-2010, 06:14 AM
  #9  
10 Second Club
Thread Starter
iTrader: (1)
 
jdaniel's Avatar
 
Join Date: Dec 2004
Posts: 359
Likes: 0
Received 2 Likes on 2 Posts
Default

Thanks, guys!!
Old 01-25-2010, 10:16 AM
  #10  
Launching!
iTrader: (14)
 
viper9403's Avatar
 
Join Date: Jan 2005
Location: Belton, Tx
Posts: 246
Likes: 0
Received 0 Likes on 0 Posts

Default

Nice 60ft. What is done to the rear to hold up to those launches?
Old 01-25-2010, 11:49 AM
  #11  
10 Second Club
Thread Starter
iTrader: (1)
 
jdaniel's Avatar
 
Join Date: Dec 2004
Posts: 359
Likes: 0
Received 2 Likes on 2 Posts
Default

Thanks, man! Nothing but 300M output shafts on both sides. Also running a 4.10 gear but thats not there for strength. LOL
Old 01-25-2010, 12:40 PM
  #12  
11 Second Club
iTrader: (18)
 
Justins00ss's Avatar
 
Join Date: Mar 2007
Location: Eastern Ma/ PSL florida
Posts: 845
Likes: 0
Received 9 Likes on 4 Posts

Default

Damn man I need a 2step for my f-body. Thats hauling *** for sure man, good job
Old 01-25-2010, 12:52 PM
  #13  
TECH Resident
iTrader: (7)
 
01SuperSport's Avatar
 
Join Date: Jul 2006
Location: San Fernando Valley, CA
Posts: 846
Likes: 0
Received 2 Likes on 2 Posts

Default

SICK!!!!! In the good way of course
Old 01-25-2010, 01:05 PM
  #14  
Launching!
iTrader: (14)
 
viper9403's Avatar
 
Join Date: Jan 2005
Location: Belton, Tx
Posts: 246
Likes: 0
Received 0 Likes on 0 Posts

Default

Originally Posted by jdaniel
Thanks, man! Nothing but 300M output shafts on both sides. Also running a 4.10 gear but thats not there for strength. LOL
Good deal. Car rolls out pretty hard. You race out at TAD?

Last edited by viper9403; 01-25-2010 at 05:35 PM.
Old 01-25-2010, 06:09 PM
  #15  
10 Second Club
Thread Starter
iTrader: (1)
 
jdaniel's Avatar
 
Join Date: Dec 2004
Posts: 359
Likes: 0
Received 2 Likes on 2 Posts
Default

Originally Posted by viper9403
Good deal. Car rolls out pretty hard. You race out at TAD?
Yeah I do but the last time I was out there I couldn't cut a good sixty to save my life and I asked if they would throw down some VHT and the guy got an attitude with me so I'm not a huge fan of that place anymore.
Old 01-25-2010, 07:44 PM
  #16  
TECH Fanatic
iTrader: (3)
 
algws6's Avatar
 
Join Date: Jun 2003
Location: El Paso
Posts: 1,139
Likes: 0
Received 0 Likes on 0 Posts

Default

nice. did you have to take the inner liners out to make thos 28s fit?
Old 01-25-2010, 08:06 PM
  #17  
10 Second Club
Thread Starter
iTrader: (1)
 
jdaniel's Avatar
 
Join Date: Dec 2004
Posts: 359
Likes: 0
Received 2 Likes on 2 Posts
Default

Originally Posted by algws6
nice. did you have to take the inner liners out to make thos 28s fit?
Sure did. They just barely rub but they would eventually rub a small hole. Only takes a few seconds to remove them though.
Old 01-25-2010, 08:52 PM
  #18  
Banned
iTrader: (22)
 
LS1 SPEED's Avatar
 
Join Date: Jan 2004
Location: Schaumburg,IL
Posts: 4,957
Likes: 0
Received 0 Likes on 0 Posts
Default

congrats on a great pass
Old 01-25-2010, 08:53 PM
  #19  
10 Second Club
Thread Starter
iTrader: (1)
 
jdaniel's Avatar
 
Join Date: Dec 2004
Posts: 359
Likes: 0
Received 2 Likes on 2 Posts
Default

Thanks man!
Old 01-25-2010, 08:59 PM
  #20  
11 Second Club
iTrader: (11)
 
TA1364's Avatar
 
Join Date: Aug 2007
Location: Dayton, OH
Posts: 1,779
Likes: 0
Received 3 Likes on 2 Posts

Default

Nice. So what plugs and gap are you running?



All times are GMT -5. The time now is 02:28 PM.