Drag Racing Tech - 1.42 60ft on back tires (my wheelstand video)

This is one of the videos of my car last Fri. night. I have another one that looks alot better, i will try and post it later.

http://www.ghettosledracing.com/videos/121903vid/fast98z.wmv
__________________
Mike @ MTI

'98 NBM Z-28 A3
MTI S2 5.3l Truck Heads, C1 cam, Hooker LT's, 3"y-pipe, SLP Loudmouth, Pulley, Ronnie Doris built TH350, Circle D Specialties N2o Convertor, 10 bolt w/3.23's, TNT/NOS/NX.STOCK SHORTBLOCK

Hopefully I fixed the link. :)

Looks like a true "pucker" ride. ;)

link worked..

what did it run??

Any they break when it came down??

Yea the link worked. That most be one hell of a ride. :eek2:

Looks like it came down pretty well. Since you didn't seem to bounce much I assume that you had the struts pretty stiff.

What was the time on that pass???

Looks like fun :eek2:

was that on a 10 bolt

That just plain ROCKS! :thumbup:

Looks kinda scary Mike, you are a MAN for staying in it. haha. Sorry I missed your phone calls, but it looks like you got the vid hosted anyways.

Not bad for a 12-second car! :D

Tony

I used to do that on my 18" HUFFY Roadmaster bike. No biggie.


:P ;) :eek2:

awesome run! what did it run that night? it looked great at the TR shootout.

Great video!!!! From what Mike told me nothing broke on that run. :eek2: The K-member got a little scratched. ;)

Awesome! :eek2:: I love videos like that. :thumb:

daymn! props for staying in it, looked wicked! :hail:

Nice... :drive: I wish mine would do that with my 60ft.'s... :eek2:

BADASS!!


:hail: 1 Bad Z

Thanks everyone. Nothing broke when it came down, the front QA1's were set on 4 and it scraped the FACTORY K-MEMBER a little bit. This was not on the 10 bolt rear, it now has a 12 bolt/3.73 and it's not finishing the 1/4 on the N2o(listen to rev limiter at end). I can't say just yet what it ran because a select few locals want a piece of my little stock motored LS1. But I will tell everyone before I do build a motor. Even if I did say I don't know if anyone would believe me:)

what size tire is it on?

what size tire is it on?

28-10-15 Hoosier DO5

What RPM do you trap at?
I'm trying to figure out what gear I need.(TH400 conversion)
I was planning on going with a 4.10.(27x11.5 QTPfor motor,29x10 Hoosier drag for nitrous)but maybe a 3.73.

Thanks

is this monstrocity your engin bay?


http://home.houston.rr.com/gossip/bone.jpg

is this monstrocity your engin bay?


http://home.houston.rr.com/gossip/bone.jpgLooks like some nice Steel Braided Garden Hose for Fuel Lines... :eek2:

Is that telephone wire ??

That is the picture of my engine but, the big monster fuel lines and all the wires and fu*ked up lines that you see are just a joke picture. We took this picture one Sunday just joking around. It's all fake. The only nitrous that is on it is a single NX fogger nozzle and the two solenoids that you see to the right of the throttle body.

LOL! Mike, that funny engine pic sorta looks like Sanders' engine when it first arrived at MTI, a looong time ago ;)

Hmm, tell the truth Mike , that is your new direct ported single nozzle NXMP sys. you just recently installed. I told you that fuel line was too big, 25,000 lph is definetly too much fuel for your 75 shot !!

hehe