View Full Version : 9.80's first weekend out


slooter
10-13-2010, 03:50 PM
Right now I have a 368 800 hp N/A motor,1st time out ran a 9.80's at 140mph....... 3300 lb car with driver.I have a few issues
with gear and converter,but we will figger that out one step at a time.
I was going to build another short block but a larger cubs 412,or a 420 something square like that.
I would like to run in the 8.70 range,10.5 tire.


http://i744.photobucket.com/albums/xx82/slooter6/DSC06304.jpg

Thanks for looking

Tony : )

billyflantos
10-13-2010, 06:58 PM
good looking car...

highpockets
10-13-2010, 10:37 PM
Nice job hanging the front wheels too ! Wish mine would do that just once,damn that IRS !

casper383
10-15-2010, 08:31 PM
Badass lookin car man! There is alot more left in that setup, any specs on the engine? My 364" LS2 is about done, going the N/A route as well

slooter
10-16-2010, 09:08 AM
Badass lookin car man! There is alot more left in that setup, any specs on the engine? My 364" LS2 is about done, going the N/A route as well

Hey Casper383 thanks for the good words.

368 sbc
SB2.2 Heads, titanium valves,Jessel rockers
Bowtie block with roller cam bearings
Custom built cam ,solid roller,
custom JE pistons
GRP Alumium rods
Custom COLA billet crank
aprox 14.5 to 15 to 1 compression
Belt drive oil system
Thats just off the top of my head.........?
I had LS motor in my car before,was new .....after 50 passes
put a rod out the side of the alumium block..... : (
Decided to go 1st gen stuff,parts a lot cheaper,and easier to get.

Good luck with your new combo,nice car too...... : )

Tony

slooter
10-16-2010, 11:46 AM
Here's my first 9sec pass
Sorry about the burnout I think it was the water boy first day,
he couldn't even get me in the water...... : (
Enjoy.................... ; )

Tony

http://www.youtube.com/watch?v=7rreYQnL_e0

casper383
10-16-2010, 08:02 PM
Damn that car leaves nice, motor sounds wicked! What was the 60ft on that pass? Keep us posted when you get some more E.T knocked off, good luck with it.

slooter
10-18-2010, 10:01 AM
Damn that car leaves nice, motor sounds wicked! What was the 60ft on that pass? Keep us posted when you get some more E.T knocked off, good luck with it.

The 60ft was only 1.38.....like you said there's alot in it still

slooter
10-21-2010, 07:08 AM
Could I be added to the 9sec club

Thanks Tony...... ; )

slooter
12-03-2010, 03:21 PM
How to get in the 9 sec club...............:confused:

Tony:bang:

slooter
01-14-2011, 09:34 AM
A few changes this year..................

Change rear gear from 4.10 to 4.86
Change converter from 5500 stall to 6800 stall
narrow rear end 2in on each side,get lower center
wheelie bar.........just a small one
Fine tune engine on dyno.......get best tune.

should get me in 9.30's don't u think

Tony......:D

RJE
01-27-2011, 03:57 PM
Nice car, and nice times!! Once you get everything sorted out you will really be flying. I hope to make some 9 sec passes this spring.

Randy

Turbo-T
01-27-2011, 11:31 PM
:D:nod:all i can say maybe the ford needs to give you the chute and the bars because when you left him all he could do was dream!:D

Firehawk441
01-29-2011, 06:01 PM
Hey Casper383 thanks for the good words.

368 sbc
SB2.2 Heads, titanium valves,Jessel rockers
Bowtie block with roller cam bearings
Custom built cam ,solid roller,
custom JE pistons
GRP Alumium rods
Custom COLA billet crank
aprox 14.5 to 15 to 1 compression
Belt drive oil system


Tony

Nice combo... Who did the SB2.2 heads for you?