DeLaRosa25

iTrader: (10)

Are these the ebay specials?

Bought them as "pacesetter" but after looking alot closer after the money was sent. I'm pretty sure I was dooped . They clearly are not stainless..so I'm hoping they are not ebay ones. If so..time to sell them! haha. In some pics they also look like flowtechs?

my bandit

iTrader: (10)

they do look like flowtechs... the o2 sensors are on the outside not the inside of the collector and how does the flange look? is it alittle raised up on the end of the pipe or is it smooth?

DeLaRosa25

iTrader: (10)

Smooth. It looks like they used reducers of some sort. Right where the collectors would be goes to a tad smaller piping, about 2.75". Slides right into the Y pipe that I got with the package.

6898camaross

Flowtechs cause of the dent

my bandit

iTrader: (10)

i was gonna say flowtechs because of the flange being cut.. they are not stainless so i would coat them. heres what mine looked like.. and i picked mine up for 180 bucks with a set of subframe connectors
this is what i was talking about earlier with the flange

Starz T/A 17

iTrader: (6)

FYI pacesetters do not make stainless headers for these cars, they either come in painted or coated

ANTICOP RAM AIR

iTrader: (7)

https://ls1tech.com/forums/parts-cla...h-headers.html

looks like these...

DeLaRosa25

iTrader: (10)

Damn.. How's the fitment with them when you installed yours?

DeLaRosa25

iTrader: (10)

Yea I knew that. Was just stating that all the eBay headers ive seen were stainless..unsure of this brand of there were ceramic eBay headers, was just hoping that the set I have aren't them .

God it sucks typing touch screen

my bandit

iTrader: (10)

my fitment wasnt too bad. i had to remover the oil filter breather? its a little metal piece above the oil filter. i had to remove the heat sheild on the drivers side also. you might need to notch the k-member also. mine was done already but it needed alittle more but oh well. other then that it was decient for the price. they do tuck very nice though

DeLaRosa25

iTrader: (10)

That's good to know info!!! What size 02extensions are you using???

Hope my ory is pacesetter at least. Has the 2 flat spots like the stock Y and pacesetter is the only aftermarket Ypipe that I know has the flats

camaroboy14

iTrader: (8)

Hey OP how much did u get those for??

TImmy_Jones

iTrader: (4)

Is that some sort of X pipe/Dual setup you bought with them? Do share..

DeLaRosa25

iTrader: (10)

Nope, I purchased the LT/ORY from a member on here

X pipe was not included with my purchase. Bought from a local fbody forum member. For the price couldn't pass it up. If I switch to td's, would be selling my lm1 cb to my friend and cutting off my magnaflow bullet and will order one more just like it. I like the way a td w/ magnaflow bullets sound

my bandit

iTrader: (10)

im just using regular extensions but im going to switch to the vette o2 sensors (bosch 13111 i think). my flowtech y had some indentions in it also, just just so it tucks better and doesnt bang. but yours looks different. my merge blows

jarheadtex

iTrader: (2)

What brand are those sandals?

DeLaRosa25

iTrader: (10)

Lol...walmart hahaha

DeLaRosa25

iTrader: (10)

Well in the pic is an xpipe. I'll have to unpack the y pipe and snap a pic..maybe my ORY is pacesetter

my bandit

iTrader: (10)

my flowtech Y was crap... but i still installed it and it works so thats all that mattered to me..