Stereo & Electronics - Dynomatted Today

Phew, took me about 6 hours but The rear seats, rear 1/4s, and doors are done! I had ordered some Dynaxorb for behind the mids, but the company cancelled my order and told me they couldn't get it any more :( . Still need to get some MLV to quiet my gears down.

http://farm9.staticflickr.com/8011/7167856500_c63056ed12_b.jpg (http://www.flickr.com/photos/74632166@N04/7167856500/)
IMG_1994 (http://www.flickr.com/photos/74632166@N04/7167856500/) by KKloppe (http://www.flickr.com/people/74632166@N04/), on Flickr


I'm still undecided on whether to do the Floor and Roof.

Nice!

I did the ENTIRE interior and I think it was around 20 hours. Worked mostly sunday afternoons and it took me a couple visits to finish it.

What is MLV For the Gears?

do i spy some 0 gauge wire? whats your trunk, yo?

not only does that look like 0ga, but is that knu koncepts kolossus fleks?

What is MLV For the Gears?

Mass loaded Vinyl

It is an extremely effective sound blocker, unlike dynamat and similar products which may cut noise a little but are primarily for vibration. We are talking 30+db's quieter for the mid-high frequencies.

MLV weighs about a lb a sq foot so I'm only going to put it behind the rear seats and over the wheel wells.

do i spy some 0 gauge wire? whats your trunk, yo?

http://farm8.staticflickr.com/7083/7168205980_244836be69_b.jpg (http://www.flickr.com/photos/74632166@N04/7168205980/)
IMG_0077 (http://www.flickr.com/photos/74632166@N04/7168205980/) by KKloppe (http://www.flickr.com/people/74632166@N04/), on Flickr

Still undecided as to what Sub to go with. But I am leaning towards a JL 8w7AE sealed between the rear seats on top of the driveshaft in the Cabin. There is a Gas tank between the Cabin and the Trunk and I'd like to have my trunk space.

Full Specs

HU: IDA-X305s with Imprint Module (Changing to INE-S920 once they come out)
Front Components: JL C5 6.5" crossed @ 100hz
Rear Componenets: JL C2 6.5" crossed @ 120hz
Rear Deck: JL Zr 800cw Bandpass 45hz-200hz
Sub: Undecided crossed @ 85hz

Amp1: JL A4300 bridged to fronts
Amp2: JL G4500 to rear components
Amp3: JL G1300 to rear deck
Amp4: JL G1700 to Undecided

Doors, Rear 1/4, Rear Seats, and Trunk Lid have dynomat


Here is the system in my last car
http://farm9.staticflickr.com/8008/6997873232_26835bdd1a_b.jpg (http://www.flickr.com/photos/74632166@N04/6997873232/)
Subs (http://www.flickr.com/photos/74632166@N04/6997873232/) by KKloppe (http://www.flickr.com/people/74632166@N04/), on Flickr

Full Specs

HU: IDA-X305s with Imprint Module (Changing to INE-S920 once they come out)
Front Components: JL C5 6.5" crossed @ 100hz
Rear Componenets: JL C2 6.5" crossed @ 120hz
Rear Deck: JL Zr 800cw Bandpass 45hz-200hz
Sub: Undecided crossed @ 85hz

Amp1: JL A4300 bridged to fronts
Amp2: JL G4500 to rear components
Amp3: JL G1300 to rear deck
Amp4: JL G1700 to Undecided

http://28.media.tumblr.com/tumblr_lp77d9TZrj1r0yhazo1_400.jpg

very nice.

why so many 4ch amps to the speakers instead of something putting out more power per channel?

why so many 4ch amps to the speakers instead of something putting out more power per channel?

I have 2 4ch amps and 2 mono's. The 300w mono runs the midbass and the 700w mono runs the Sub. The 2 4channels is because I may or may not go 3 way active instead of passive.

Right now one of the 4 channels is bridged to the front, so there is only 2 spare channels in the system.

nicely modded cars. Whats the color of the lexus?

nicely modded cars. Whats the color of the lexus?

Garnet Pearl paint code 3k3