APE and Absolute speed
#1
Banned
Thread Starter
Join Date: Oct 2003
Location: Texas
Posts: 417
Likes: 0
Received 0 Likes
on
0 Posts
APE and Absolute speed
I just wanted to thank Nick at APE for doing research on some custom pistons I ordered and getting the right rods that NO ONE seemed to be able to figure out..He took time out of his busy schedule and researched until he found what I was needing....THANK YOU APE AND YOU HAVE EARNED MY BUSINESS
Now for Jay @ Absolute speed.....
I had a cam made for me...pretty big...through cam motion. Jay advised me to flycut the pistons to make sure I had no P to V clearence issues. I did this, but evidently my cam was still too big and on start up, a few of the intake valves contacted the pistons damaging the BRAND NEW HEADS. To make a long story short...I called up Jay and he told me not to worry about a thing...Send him back the heads and he would havee another set out to me ASAP AT NO CHARGE...I couldnt believe my ears. I have been working closely with Jay on my project and getting the right setup...He has to have the BEST customer service I have ever dealt with....Thanks alot
Now for Jay @ Absolute speed.....
I had a cam made for me...pretty big...through cam motion. Jay advised me to flycut the pistons to make sure I had no P to V clearence issues. I did this, but evidently my cam was still too big and on start up, a few of the intake valves contacted the pistons damaging the BRAND NEW HEADS. To make a long story short...I called up Jay and he told me not to worry about a thing...Send him back the heads and he would havee another set out to me ASAP AT NO CHARGE...I couldnt believe my ears. I have been working closely with Jay on my project and getting the right setup...He has to have the BEST customer service I have ever dealt with....Thanks alot
#3
TECH Fanatic
iTrader: (6)
Join Date: Nov 2001
Location: Las Vegas
Posts: 1,101
Likes: 0
Received 0 Likes
on
0 Posts
damn good of Jay, honestly he didnt even have to do that for you. It was clearly not his fault. Hes a great guy. I hope everything comes together quickly for you. Atleast this time you will have a strong bottom end and pistons already notched. Good luck. Your car should be killer.
#5
TECH Fanatic
iTrader: (2)
Join Date: Dec 2002
Location: Orange county n.y.
Posts: 1,107
Likes: 0
Received 0 Likes
on
0 Posts
Now for Jay @ Absolute speed.....
I had a cam made for me...pretty big...through cam motion. Jay advised me to flycut the pistons to make sure I had no P to V clearence issues. I did this, but evidently my cam was still too big and on start up, a few of the intake valves contacted the pistons damaging the BRAND NEW HEADS. To make a long story short...I called up Jay and he told me not to worry about a thing...Send him back the heads and he would havee another set out to me ASAP AT NO CHARGE...I couldnt believe my ears. I have been working closely with Jay on my project and getting the right setup...He has to have the BEST customer service I have ever dealt with....Thanks alot If this delay's my new heads i'll be looking for ya J/K Anyway it's very nice to hear that Jay's taking care of you Waiting on my 2.5's great power and service is hard to beat
I had a cam made for me...pretty big...through cam motion. Jay advised me to flycut the pistons to make sure I had no P to V clearence issues. I did this, but evidently my cam was still too big and on start up, a few of the intake valves contacted the pistons damaging the BRAND NEW HEADS. To make a long story short...I called up Jay and he told me not to worry about a thing...Send him back the heads and he would havee another set out to me ASAP AT NO CHARGE...I couldnt believe my ears. I have been working closely with Jay on my project and getting the right setup...He has to have the BEST customer service I have ever dealt with....Thanks alot If this delay's my new heads i'll be looking for ya J/K Anyway it's very nice to hear that Jay's taking care of you Waiting on my 2.5's great power and service is hard to beat
Trending Topics
#8
Banned
Thread Starter
Join Date: Oct 2003
Location: Texas
Posts: 417
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Nick@AP-Engineering
Thanks for the kinds words, I am just glad I could help.
Im glad you did,Nick...Otherwise I would just have a set of new pistons laying around for paperweights
#9
10 Second Club
iTrader: (4)
Join Date: Nov 2001
Location: New to South Carolina
Posts: 910
Likes: 0
Received 0 Likes
on
0 Posts
Great news Hugger,I see that you are going with a stout set up and should run the numbers.BTW,good color choice,do you know your build number? Mine is 1912.
Jay at Absolute Speed has great customer service and is always willing to answer all your questions.
Jay at Absolute Speed has great customer service and is always willing to answer all your questions.