WTB: Rear end 4 2000 Z28
#1
On The Tree
Thread Starter
Join Date: Mar 2005
Location: Chattanooga, tn
Posts: 180
Likes: 0
Received 0 Likes
on
0 Posts
WTB: Rear end 4 2000 Z28
Just as it states, I am looking for something that fits with no mods to it, must be close shipping is to expensive I am in N.Ga SE. TN Pm me.
#3
11 Second Club
iTrader: (8)
Join Date: Jan 2002
Location: SILSBEE TX
Posts: 1,782
Likes: 0
Received 0 Likes
on
0 Posts
I do have a complete 10 bolt from a 2000 camaro
complete all new bearing/Detroit Locker/3.73/AMA cover with stud kit/mos axles with reluctor rings/4 channel /backing plates,no rotors/welded tubes/weld on relocate brackets for lower control arm
500 + shipping or pick up.
unit housing has 74 k miles, 3 k miles on complete rebuild -locker, gear, bearings,axles
Pulled to add 9"
ps will add Lockwood traction action boxed lower control arms ( I will need to chk fit after I added relocate brackets? )
Johnny
complete all new bearing/Detroit Locker/3.73/AMA cover with stud kit/mos axles with reluctor rings/4 channel /backing plates,no rotors/welded tubes/weld on relocate brackets for lower control arm
500 + shipping or pick up.
unit housing has 74 k miles, 3 k miles on complete rebuild -locker, gear, bearings,axles
Pulled to add 9"
ps will add Lockwood traction action boxed lower control arms ( I will need to chk fit after I added relocate brackets? )
Johnny
#5
On The Tree
Thread Starter
Join Date: Mar 2005
Location: Chattanooga, tn
Posts: 180
Likes: 0
Received 0 Likes
on
0 Posts
Aftermarket or heavy duty rear, already set up for my car.
Thanks Johnny, I just bought Lowers, and will talk to my builder about your 10 bolt, Sorry I am not very technical, I do make over 500 to the tires, do you have any idea what this rear will hold? Oh and where are you, state wise? EDIT, I see now TX !
Not sure on the ans, but my car does not have TC.
Again thanks everyone.
I do have a complete 10 bolt from a 2000 camaro
complete all new bearing/Detroit Locker/3.73/AMA cover with stud kit/mos axles with reluctor rings/4 channel /backing plates,no rotors/welded tubes/weld on relocate brackets for lower control arm
500 + shipping or pick up.
unit housing has 74 k miles, 3 k miles on complete rebuild -locker, gear, bearings,axles
Pulled to add 9"
ps will add Lockwood traction action boxed lower control arms ( I will need to chk fit after I added relocate brackets? )
Johnny
complete all new bearing/Detroit Locker/3.73/AMA cover with stud kit/mos axles with reluctor rings/4 channel /backing plates,no rotors/welded tubes/weld on relocate brackets for lower control arm
500 + shipping or pick up.
unit housing has 74 k miles, 3 k miles on complete rebuild -locker, gear, bearings,axles
Pulled to add 9"
ps will add Lockwood traction action boxed lower control arms ( I will need to chk fit after I added relocate brackets? )
Johnny
Not sure on the ans, but my car does not have TC.
Again thanks everyone.
#7
11 Second Club
iTrader: (8)
Join Date: Jan 2002
Location: SILSBEE TX
Posts: 1,782
Likes: 0
Received 0 Likes
on
0 Posts
Aftermarket or heavy duty rear, already set up for my car.
Thanks Johnny, I just bought Lowers, and will talk to my builder about your 10 bolt, Sorry I am not very technical, I do make over 500 to the tires, do you have any idea what this rear will hold? Oh and where are you, state wise? EDIT, I see now TX !
Not sure on the ans, but my car does not have TC.
Again thanks everyone.
Thanks Johnny, I just bought Lowers, and will talk to my builder about your 10 bolt, Sorry I am not very technical, I do make over 500 to the tires, do you have any idea what this rear will hold? Oh and where are you, state wise? EDIT, I see now TX !
Not sure on the ans, but my car does not have TC.
Again thanks everyone.
I run 1.64'/tires/ NO way close to 500 ,
NO I would not trust it to last very long
good luck, Johnny