Strokers and Nitrous
#1
11 Second Club
Thread Starter
iTrader: (1)
Join Date: Oct 2003
Location: Granbury Texas
Posts: 691
Likes: 0
Received 0 Likes
on
0 Posts
Strokers and Nitrous
I am about to install the TNT kit with a 150 shot in my 395 stroker and was wandering if anyone else has tried this combo, and what to expect.
I make about 475-485 rwhp on motor and just ran my best pass of 11.6 @ 121, this was done at 4000' and with Nitto drag radials so I figure it not too bad. I am going to get some 17" MT drag radials and was hoping to run mid 10s with this set-up.
Anybody have some stroker numbers with Nitrous?
I make about 475-485 rwhp on motor and just ran my best pass of 11.6 @ 121, this was done at 4000' and with Nitto drag radials so I figure it not too bad. I am going to get some 17" MT drag radials and was hoping to run mid 10s with this set-up.
Anybody have some stroker numbers with Nitrous?
#4
TECH Addict
Join Date: Feb 2002
Location: Lewisville, Texas
Posts: 2,319
Likes: 0
Received 0 Likes
on
0 Posts
9.23@149.1 on a 1.37 60ft from a 408 making 478RWHP/?RWTQ on motor and 723RWHP/666RWTQ on a 300 shot making 250 to the ground.
Last edited by Elite_Hot_Rod; 05-04-2005 at 12:22 AM.
#5
Originally Posted by David Gordon
I am about to install the TNT kit with a 150 shot in my 395 stroker and was wandering if anyone else has tried this combo, and what to expect.
I make about 475-485 rwhp on motor and just ran my best pass of 11.6 @ 121, this was done at 4000' and with Nitto drag radials so I figure it not too bad. I am going to get some 17" MT drag radials and was hoping to run mid 10s with this set-up.
Anybody have some stroker numbers with Nitrous?
I make about 475-485 rwhp on motor and just ran my best pass of 11.6 @ 121, this was done at 4000' and with Nitto drag radials so I figure it not too bad. I am going to get some 17" MT drag radials and was hoping to run mid 10s with this set-up.
Anybody have some stroker numbers with Nitrous?
This is off the topic, but you might want to consider a 15" or 16" rim. The more sidewall you have, the better traction you get. 17" get lousy traction due to no sidewall depth....
#6
11 Second Club
Thread Starter
iTrader: (1)
Join Date: Oct 2003
Location: Granbury Texas
Posts: 691
Likes: 0
Received 0 Likes
on
0 Posts
I cant get anything smaller than 17" on my car without grinding something which I am not willing to do. I will get my 60' down with the new MT drag radials. Also a 1.65 is considered very good at our track, most F-body with small converters only get 1.8s here and a stock f-body runs mid 14s.
#7
On The Tree
iTrader: (2)
Join Date: Oct 2003
Location: Abilene, Texas
Posts: 148
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by David Gordon
I am about to install the TNT kit with a 150 shot in my 395 stroker and was wandering if anyone else has tried this combo, and what to expect.
I make about 475-485 rwhp on motor and just ran my best pass of 11.6 @ 121, this was done at 4000' and with Nitto drag radials so I figure it not too bad. I am going to get some 17" MT drag radials and was hoping to run mid 10s with this set-up.
Anybody have some stroker numbers with Nitrous?
I make about 475-485 rwhp on motor and just ran my best pass of 11.6 @ 121, this was done at 4000' and with Nitto drag radials so I figure it not too bad. I am going to get some 17" MT drag radials and was hoping to run mid 10s with this set-up.
Anybody have some stroker numbers with Nitrous?
<----Assuming you ran at Penwell.