Jumping Out Of 4TH Gear
03-14-2006, 01:41 PM
#1
On The Tree
Thread Starter
iTrader: (21)
Join Date: Jul 2005
Location: Alex. Louisiana
Posts: 126
Likes: 0
Received 0 Likes
on
0 Posts
Jumping Out Of 4TH Gear NEW CLUTCH,REBUILT TRANS,UP SHIFTS GREAT BUT WHEN YOU DOWNSHIFT FROM FIFTH TO FOURTH IT JUMPS OUT OF GEAR.ALSO,SLOWING DOWN IN FOURTH IT WILL JUMP OUT OF GEAR.EVERYTHING ESLE IS FINE JUST SPITTING OUT OF FOURTH GEAR.TRIED MOVING GEAR STOP BACK ON SHIFTER IN FOURTH & BLED THE CLUTCH SYSTEM OF ANY AIR BUBBLES! DONT KNOW WHAT ESLE TO DO. 
ANY SUGGESTIONS?
ANY SUGGESTIONS? 
03-14-2006, 11:48 PM
#2
12 Second Club
iTrader: (52)
Join Date: Mar 2006
Location: Michigan
Posts: 699
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by LS1ROPER
NEW CLUTCH,REBUILT TRANS,UP SHIFTS GREAT BUT WHEN YOU DOWNSHIFT FROM FIFTH TO FOURTH IT JUMPS OUT OF GEAR.ALSO,SLOWING DOWN IN FOURTH IT WILL JUMP OUT OF GEAR.EVERYTHING ESLE IS FINE JUST SPITTING OUT OF FOURTH GEAR.TRIED MOVING GEAR STOP BACK ON SHIFTER IN FOURTH & BLED THE CLUTCH SYSTEM OF ANY AIR BUBBLES! DONT KNOW WHAT ESLE TO DO. ANY SUGGESTIONS?
ANY SUGGESTIONS?i have a few obvious things but worth checking
check the linage,is the trans case lined up properly and tight?
was it professionally rebuilt?
03-15-2006, 03:57 AM
#3
On The Tree
Thread Starter
iTrader: (21)
Join Date: Jul 2005
Location: Alex. Louisiana
Posts: 126
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by 89Formulaws6
i have a few obvious things but worth checking
check the linage,is the trans case lined up properly and tight?
was it professionally rebuilt?
check the linage,is the trans case lined up properly and tight?
was it professionally rebuilt?
Yes alignment is good and trans is tight.Yes trans was rebuilt by a sponsor.
03-15-2006, 10:56 AM
#5
12 Second Club
iTrader: (52)
Join Date: Mar 2006
Location: Michigan
Posts: 699
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Exotic Performance Plus
I would call whoever rebuilt (or had it rebuilt) for you, and explain the situation. It sounds like an internal transmission problem to me. Bob
agreed possibly the syncro wasn't put together right maybe
03-15-2006, 12:32 PM
#6
Launching!
iTrader: (70)
Join Date: Oct 2005
Location: OHIO
Posts: 225
Likes: 0
Received 0 Likes
on
0 Posts
i had the same problem in my 00ws6 i kept jumpin out of 2nd and reverse i had to get new syncros and forks on thoses gears. if i can get pics of the old syncros i can show you why they jump outa gear its kinda neat
03-15-2006, 12:45 PM
#7
12 Second Club
iTrader: (52)
Join Date: Mar 2006
Location: Michigan
Posts: 699
Likes: 0
Received 0 Likes
on
0 Posts
it could even be the shift fork as well. I didn't think reverse gear wasn't syncronized but i don't know alot about the t56 yet only the t5.
simple things during putting the mainshaft together have cause a syncro to get messed up, the inserts not properly seated, lock rings not put in right, even the syncro sleeve not put on right. too many to list
simple things during putting the mainshaft together have cause a syncro to get messed up, the inserts not properly seated, lock rings not put in right, even the syncro sleeve not put on right. too many to list
