A/C Delete... Do I need this?
11-14-2006, 06:54 PM
#1
TECH Veteran
Thread Starter
iTrader: (14)
Join Date: Apr 2005
Location: N. Falmouth MA
Posts: 4,085
Likes: 0
Received 0 Likes
on
0 Posts
A/C Delete... Do I need this Part? This shroud that goes in front of the Condensor. There's nothing to attatch it to the radiator. What about the rest of the plastic air dam stuff there, can I remove it as well? Or will it effect my cooling?
As far as the delete, it was easy. About an hour worth of work. I removed everything except for the evaporator. Brackets and all.
As far as the delete, it was easy. About an hour worth of work. I removed everything except for the evaporator. Brackets and all.
Last edited by bayer-z28; 11-14-2006 at 07:05 PM.
11-14-2006, 07:55 PM
#5
TECH Veteran
Thread Starter
iTrader: (14)
Join Date: Apr 2005
Location: N. Falmouth MA
Posts: 4,085
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Coy
You live in New Mexico, and deleted your A/C? 
^^blkbird is from TX and living w/o AC..
Originally Posted by evrae205
got a walkthrough you used. or maybe a write up you did?
1- Disconnect the airbox lid and basically anything that goes up to the throttle body.
1.5- Remove the belt. 15mm fits the tensioners. You'll have to egt the main belt out of the way first. Than the A/C belt.
2- 4 10mm bolts hold the rad support on... disconnect it.
2.5- Manage to fenagle the plasic shroud out of the way. (you'll have to slightly push the radiator back)
3- one 10mm bolt on the high side connection to the condensor (front)
4- 2 14mm bolts hold the high and low connections to the evaporator ports. (pass side going into the car) Disconnect low pressure cut off switch before you CAN remove the line.
5- reciever/dryer canister is held in place by a bracket. One 10mm bolt to loosten it.
6- go underneath- unbolt one 13mm (I think) bolt that holds both lines to the back of the pump. (lines will not come out yet)
7- 4 15mm bolts hold the pump in place. Unclip the clutch electric line first, or after the pump is loose. (I did this on the ground w/o jack stand, or ramps, so I had to wait till the pump was loose) Disconnect the pump and it slides out.
8- one 14mm bolt that holds the bottom line to the condensor. disconnect it and NOW the lines will come out.
9- 4 15mm bolts hold the pump bracket in place. -Disconnect it and it slides out.
Voila!... it out. Just bolt the radiator support back up, and put the lid, MAF and bellows back on... and don't forget to plug the sonsors back in. The reciever/dryer canister bracket is held in by a TX bit. I am unsure of the size, but I managed to get it out with an allen wrench.
Last edited by bayer-z28; 11-14-2006 at 08:08 PM.
Trending Topics
11-14-2006, 10:20 PM
#8
Originally Posted by bayer-z28
It was gonna cost me $870 to get it fixed. So I said fk it... Weight reduction. I've lived here over a year and I can handle the heat. AC= windows and 65mph...It hasn't worked in years. Pluss if I REALLY want it back I can reinstall it and take it to the dealer to have them pull a vaccuum to find leaks, fix and recharge it.
11-15-2006, 01:23 AM
#10
Launching!
Join Date: Feb 2006
Location: McAllen, TX
Posts: 202
Likes: 0
Received 0 Likes
on
0 Posts
i removed that air damn a couple years ago couldnt remember how to put it back after a while now it just collects dust in my closet. no problems with cooling or anything still curious as to how it goes
