Car Is Done!!!
09-09-2008, 10:23 PM
#1
12 Second Club
Thread Starter
iTrader: (6)
Join Date: Jul 2006
Posts: 419
Likes: 0
Received 0 Likes
on
0 Posts
Car Is Done PICS AND VIDS NOW!! Well its been a long time coming, but my Trans AM is back on the road
MS4
Ported FAST 90/NW
Fully ported 241's with 3 angle valve job
ARH 1 3/4 Long tubes w/catted Y
SLP Loudmouth 2
Nasty performance stage 1 fuel kit( Rails, Walbro pump, #42's hotwire kit)
Harland Sharp 1:8 rockers
Fast Toys Ram Air
85mm Maf and Lid
Spec 2+ w/alum flywheel
Ram Adj master cylinder
All UMI rear suspension single adjustable (lower control arms, panhard, tunnel mounted torque arm)
Eaton Posi
4.10's
Moser axles
TA Stud Girdle
Car was dyno tuned at RPM in DE 428RWHP
MS4
Ported FAST 90/NW
Fully ported 241's with 3 angle valve job
ARH 1 3/4 Long tubes w/catted Y
SLP Loudmouth 2
Nasty performance stage 1 fuel kit( Rails, Walbro pump, #42's hotwire kit)
Harland Sharp 1:8 rockers
Fast Toys Ram Air
85mm Maf and Lid
Spec 2+ w/alum flywheel
Ram Adj master cylinder
All UMI rear suspension single adjustable (lower control arms, panhard, tunnel mounted torque arm)
Eaton Posi
4.10's
Moser axles
TA Stud Girdle
Car was dyno tuned at RPM in DE 428RWHP
Last edited by fatdave; 09-12-2008 at 09:49 PM.
09-09-2008, 10:29 PM
#2
11 Second Club
iTrader: (34)
Join Date: Feb 2005
Location: Ft. Wayne, Indiana
Posts: 3,158
Likes: 0
Received 0 Likes
on
0 Posts
Congrats, I just got mine back on the road after almost 2 years. My only question would be....will the Spec 2+ hold the power you will be making?? might need an upgrade there.
09-10-2008, 07:51 PM
#4
Banned
Join Date: Jan 2008
Location: Las Vegas
Posts: 121
Likes: 0
Received 0 Likes
on
0 Posts
09-10-2008, 09:48 PM
#5
12 Second Club
Thread Starter
iTrader: (6)
Join Date: Jul 2006
Posts: 419
Likes: 0
Received 0 Likes
on
0 Posts
I loved the stage 1 I had put on my old 97Z so I wanted to go with them again. It feels great so far but I am still breaking it in. If i end up not happy with it I will probably go with a textralia.
Trending Topics
09-12-2008, 08:43 PM
#9
12 Second Club
Thread Starter
iTrader: (6)
Join Date: Jul 2006
Posts: 419
Likes: 0
Received 0 Likes
on
0 Posts
no track times yet still have a few hundred more miles untill the clutch is all broken in.
Here are some pics and vids of the car. Will get some better ones when its nice and I get the car outside.
Thanks for all the comments guys. I want to thank a couple of site sponsors for their help with getting this thing done. Fran at Race Proven Motorsports. He is a great guy and knows he stuff. All the guys at Texas Speed. they were always great and willing to help, LOVE MY MS4. WS6store.com Great people to deal with good prices!!
Here are some pics and vids of the car. Will get some better ones when its nice and I get the car outside.
Thanks for all the comments guys. I want to thank a couple of site sponsors for their help with getting this thing done. Fran at Race Proven Motorsports. He is a great guy and knows he stuff. All the guys at Texas Speed. they were always great and willing to help, LOVE MY MS4. WS6store.com Great people to deal with good prices!!
09-12-2008, 09:21 PM
#11
12 Second Club
Thread Starter
iTrader: (6)
Join Date: Jul 2006
Posts: 419
Likes: 0
Received 0 Likes
on
0 Posts
1.8 was the stock size and I wanted to stay with that could not go to a bigger size due to the close PVC and did not see any reason to go to a smaller size rocker. Thanks.
