Nasty Performance Polished Billet Fuel Rails & lines
09-16-2012, 04:42 PM
#1
Nasty Performance Polished Billet Fuel Rails & lines Category: Engine - Intake/Fuel
Price: $280
Part Fits: 2010+ Camaro, 93-02 Chevrolet Camaro, 93-02 Pontiac Firebird, Corvette, 04-06 Pontiac GTO, 04+ Cadillac CTS-V
Location (State): SC
Item Condition: Used
Shipping Information: Item Can be Shipped
Engine: LS2/LS3/LS7/L92/LS9, LS1/LS6
LS Engine?: Fits LS Engine
Here are some pics:
They have a few very slight scratches on them from use. The fittings have a few nicks here and there from tightening down and loosening etc. The polishing is not 100% but it looks about as good as it can with a dremel and polishing wheel.
****You will need to purchase a new set of o-rings for installment as the ones on these were pretty galled up and should not be reused so I am not including them. The o-rings are just a couple dollars from Nate @ Nasty Performance. Also, you will need the plastic clip that goes on the inside of the feed line that connects to the actual metal feed line coming from the tank. Again probably a couple dollars if that.****
The rails go for $250.00 brand new from Nate, and the feed line kit goes for $130.00 right now.
I am including some extra line and fittings so I am asking $300 shipped OBO, but I'm open to offers.
PM for any interest! Thank you!
Last edited by djfury05; 09-28-2012 at 08:04 PM.
09-17-2012, 12:13 AM
#2
Teching In
Join Date: Sep 2011
Location: springfield, mo
Posts: 24
Likes: 0
Received 0 Likes
on
0 Posts
I've got a pair of Nasty Performance polished billet fuel rails -8an with stainless braided crossover line and feed line. Just wetsanded and polished before these pics today by yours truly. I am including some extra line and a couple extra fittings as well. These rails will fit the LS1, LS6, Fast 78, 90, & 92mm intakes. They will not fit the Fast 102 LSXR!
Here are some pics:
They have a few very slight scratches on them from use. The fittings have a few nicks here and there from tightening down and loosening etc. The polishing is not 100% but it looks about as good as it can with a dremel and polishing wheel.
****You will need to purchase a new set of o-rings for installment as the ones on these were pretty galled up and should not be reused so I am not including them. The o-rings are just a couple dollars from Nate @ Nasty Performance. Also, you will need the plastic clip that goes on the inside of the feed line that connects to the actual metal feed line coming from the tank. Again probably a couple dollars if that.****
The rails go for $250.00 brand new from Nate, and the feed line kit goes for $130.00 right now.
I am including some extra line and fittings so I am asking $300 shipped OBO, but I'm open to offers.
PM for any interest! Thank you!
Here are some pics:
They have a few very slight scratches on them from use. The fittings have a few nicks here and there from tightening down and loosening etc. The polishing is not 100% but it looks about as good as it can with a dremel and polishing wheel.
****You will need to purchase a new set of o-rings for installment as the ones on these were pretty galled up and should not be reused so I am not including them. The o-rings are just a couple dollars from Nate @ Nasty Performance. Also, you will need the plastic clip that goes on the inside of the feed line that connects to the actual metal feed line coming from the tank. Again probably a couple dollars if that.****
The rails go for $250.00 brand new from Nate, and the feed line kit goes for $130.00 right now.
I am including some extra line and fittings so I am asking $300 shipped OBO, but I'm open to offers.
PM for any interest! Thank you!
