BBC632Camaro

iTrader: (82)

Category: Engine - Power Adders
Price: $2150
Part Fits: 2010+ Camaro, 93-02 Chevrolet Camaro, 93-02 Pontiac Firebird, Corvette
Location (State): SD
Item Condition: Used
Shipping Information: Item Can be Shipped
Engine: LS2/LS3/LS7/L92/LS9, LS1/LS6
LS Engine?: Fits LS Engine

Custom supercharger setup... This Eaton 122 supercharger uses ls3 heads and runs on the 98-02 Camaro/Firebird belt line and front accessories. Setup is very low mount for good hood clearance. Comes with everything as seen in the pics and all the bolts/hardware to mount it and everything. Unit made 13lbs boost on a 6.0L lq4. Would also work great with an underdrive pulley or larger top pulley if you don't need that much boost. Only 3k miles on it since new. Ready to go! Works great, no problems... Only selling cause I'm building an ls7.

Fast Fuel Rails
LS9 injectors
Uses a 4 bolt 90mm TB(TB not included)

Everything for $2650
Price drop.... $2150

BBC632Camaro

iTrader: (82)

Open to offers.....

Sinistersilverado

What kind of power did u make? Wat was ur set up more less? Also will u ship? I'm interested....

BBC632Camaro

iTrader: (82)

Yes I can ship the unit. Setup was in a 4,000lb car, 6.0l w/4l80e and 3.36 gears and made very good power. Was a VERY noticeable difference when it was taken off. Boost came on right away with a touch of the throttle. Unfortunately I can't give you any dyno numbers since the car was never dyno'd since there's noone in the area that does that where I live but had to be around the 700 range...

LsXRs

iTrader: (42)

that looks nice too bad i dont have a ls3 heads

rons 00z

iTrader: (10)

ever run it at the track? what kind of MPH did it put down?

BBC632Camaro

iTrader: (82)

Lots of interest but no takers yet. Very nice setup for cheap horsepower here.

Never got a chance to run it at the track. Car doesn't have a cage either so not sure they would have let me

donnie_19

Bump for nice set up.

BBC632Camaro

iTrader: (82)

Thanks! Lots of interest and offers but no $ yet. Not holding for anyone. Great setup here

roninsonic

iTrader: (3)

Pics of it installed?

kyphur

iTrader: (5)

Were you able to fit it under the stock 4th gen hood?

BBC632Camaro

iTrader: (82)

I couldn't tell ya for sure. I don't have a car like that around to do any measuring. I had it in an old muscle car with plenty of room.

krwyellowZ28

iTrader: (10)

Any idea what your IAT's were since its a hot air setup? How much timing were you running? Is it built off a Maggie base?

BBC632Camaro

iTrader: (82)

Yes it is. Not sure what my IAT's were. They were taken from the air inlet and not in the manifold so I wondered the same thing myself. I'm not a tuner, but IIRC the timing was set conservatively low anywhere from 14-19 and we ran the fueling a little richer than normal as well..

roninsonic

iTrader: (3)

1: Measure it from the base to the top so we have a basic idea of size

2: POST SOME PICTURES. You will NOT sell anything without pictures.

Verz

iTrader: (21)

Similar setup to what ive wanted to do using that gt500 blower, what kind of base is being used or was that a custom peice? As far as IATs can alwasy run meth through it

BBC632Camaro

iTrader: (82)

Here's some more pics so you can see the height. Also thats the only install pic I have of it unfortunately before we decided to tear it apart and paint the car and it came off as well for the new setup. I'm open to all reasonable offers....

roninsonic

iTrader: (3)

damn... That thing looks at least 12-13 inches tall... No F bodies for that thing without !cowl and cutting the windshield

BBC632Camaro

iTrader: (82)

All PM's replied to...

tsquared38016

iTrader: (8)

Free bump