FS: 2004 6.0/4l80E/NP261HD 2500
#1
TECH Junkie
Thread Starter
iTrader: (12)
Join Date: Jul 2002
Location: Austin, TX
Posts: 3,422
Likes: 0
Received 0 Likes
on
0 Posts
FS: 2004 6.0/4l80E/NP261HD 2500
Category: Accessories
Price: $2500
Part Fits: 2010+ Camaro, 93-02 Chevrolet Camaro, 93-02 Pontiac Firebird, Corvette, 04-06 Pontiac GTO, 04+ Cadillac CTS-V, 67-92 Chevrolet Camaro, 67-92 Pontiac Firebird, Front wheel drive vehicles
Location (State): TX
Item Condition: Used
Shipping Information: Item Can be Shipped
Engine: LS1/LS6
LS Engine?: Fits LS Engine
6.0
4l80E
NP261HD Transfer Case
Wiring Harness
PCM
I owned the truck this came out of, it had little less than 130,000 miles on it when my buddy sideswiped an 18 wheeler in Dallas. I drove it home and pulled the complete thing out. Looking to sell it all as one piece. It has not been taken apart yet. With this I have an extra set or two of truck motor mounts, a few waterpumps and oilpumps from some other pull outs. Engine is located in my garage here in Austin.
$2800
Email is best marcus dot whitmore at gmail
#4
TECH Junkie
Thread Starter
iTrader: (12)
Join Date: Jul 2002
Location: Austin, TX
Posts: 3,422
Likes: 0
Received 0 Likes
on
0 Posts
Bump and some answers to a few questions I've had on what is extra, etc.
So do you have enough accessory parts up on your shelf in the picture for 2 engines, or are those just for the 4x4 drivetrain that we are talking about?
This is a list of the major parts I can see, there may be more I will throw in if I find it,
3 waterpumps, one is missing the pulley
1 set of truck exhaust manifolds
truck alternator and bracket
power steering pump/bracket for truck
ls1 starter
2 oil pumps,
front/rear engine covers
truck manual shift levers
valley cover
corvette crank pulley
i think there is another truck pulley somewhere
ebay ls1 to sbc mounts plates
truck taillights
Is there an intake for this engine or did you use it for your painted engine?
Yes the intake rails, injector and tb are all there
Is there an engine and transmission harness and ecm?
I have the complete engine harness and pcm up to the fusebox
If the transfer case a NP246 electric shift do you have the shift module?
No, it's a manual shift 261 HD transfer case
If its electric, do you have the buttons and harness still, if manual the levers?
Yes listed above are the manual levers, others who have done swap though prefer to use the one's for the vehicle you are using
I can tell you have the front output shaft, do you still have the rear drive shaft?
The front driveshaft is cut but does have the yolk and ujuint for the tcase side, the rear driveshaft is gone
I assume you have already gotten rid of the donor truck.
Yes, the neighbors weren't fans of the donor truck so it's gone
Can you put a complete parts list together of everything you have when you get home this evening?
The parts list is up there, those parts are in addition to the copmlete 6.0/4l80/np261 case which has the full harness pcm intake, fuel parts and the intake box and tube with maf. That setup is complete so the extra parts are just extras that you can sell on ebay and easily make several hundred back.
So do you have enough accessory parts up on your shelf in the picture for 2 engines, or are those just for the 4x4 drivetrain that we are talking about?
This is a list of the major parts I can see, there may be more I will throw in if I find it,
3 waterpumps, one is missing the pulley
1 set of truck exhaust manifolds
truck alternator and bracket
power steering pump/bracket for truck
ls1 starter
2 oil pumps,
front/rear engine covers
truck manual shift levers
valley cover
corvette crank pulley
i think there is another truck pulley somewhere
ebay ls1 to sbc mounts plates
truck taillights
Is there an intake for this engine or did you use it for your painted engine?
Yes the intake rails, injector and tb are all there
Is there an engine and transmission harness and ecm?
I have the complete engine harness and pcm up to the fusebox
If the transfer case a NP246 electric shift do you have the shift module?
No, it's a manual shift 261 HD transfer case
If its electric, do you have the buttons and harness still, if manual the levers?
Yes listed above are the manual levers, others who have done swap though prefer to use the one's for the vehicle you are using
I can tell you have the front output shaft, do you still have the rear drive shaft?
The front driveshaft is cut but does have the yolk and ujuint for the tcase side, the rear driveshaft is gone
I assume you have already gotten rid of the donor truck.
Yes, the neighbors weren't fans of the donor truck so it's gone
Can you put a complete parts list together of everything you have when you get home this evening?
The parts list is up there, those parts are in addition to the copmlete 6.0/4l80/np261 case which has the full harness pcm intake, fuel parts and the intake box and tube with maf. That setup is complete so the extra parts are just extras that you can sell on ebay and easily make several hundred back.