PST 3.5" Alum DS, Twin Turbo Kit, 241's w/BTR .660's, Stainless LT's
09-18-2013, 09:29 AM
#1
Staging Lane
Thread Starter
iTrader: (41)
Join Date: Jul 2006
Location: Warfordsburg, Pa
Posts: 97
Likes: 0
Received 0 Likes
on
0 Posts
PST 3.5" Alum DS, Twin Turbo Kit, 241's w/BTR .660's, Stainless LT's Category: Engine - Complete Motors
Price: $350
Part Fits: 2010+ Camaro, 93-02 Chevrolet Camaro, 93-02 Pontiac Firebird, Corvette, 04-06 Pontiac GTO, 04+ Cadillac CTS-V
Location (State): PA
Item Condition: Used
Shipping Information: Item Can be Shipped
Engine: LS2/LS3/LS7/L92/LS9, LS1/LS6, LT1/LT4
LS Engine?: Fits LS Engine
LS6 block (1168 casting #)
Eagle 4" stoker crank and rods
-2 cc JE pistons
Patriot Stage III LS6 heads (72cc combustion chambers)
Patriot Gold .650 lift double valve springs w/ titanium retainers
Thunder Racing 7.400 hardened pushrods
ARP head bolts
Custom ground turbo cam, but I don't know the specs
LS6 oil pump
Underdrive pulley
LS6 intake
P/P throttle body
Edelbrock High Flow fuel rails
58 lb TFS injectors with flow chart (500 miles on them)
LS7 lifters (brand new)
Stock coils with MSD plug wires
Brand new NGK plugs
Brand new GM MLS head gaskets
$5800 obo
--SOLD--
Built TH400 with B&M Ratchet shifter, 3500 stall, Reverse manual valve body, trans brake, trans cooler. $1800
--SOLD--
Next, is my Incon Twin turbo kit that's still on my Trans Am. It's capable of 827 RWHP, but I've had it on my stock bottom end making 8 lbs of boost (approx. 550 rwhp with my application) for about 4000 miles now. Never had it to the track since installed so idk any ET's for it. This kit will stay on the car until it's sold. It's not in my way and I don't need to sell it. Just thinking about an F1 400+ CI setup is all. $5000
Eboost 2 boost controller $400 --SOLD--
Stainless Longtube headers with EGR provisions very good condition $300 obo.
FAST 102 mm intake manifold for an LS3 - $600 --SOLD--
PST aluminum driveshaft for a T56 with 1350 yoke. I got it in a package deal from A99TA on here.
$350
A99TA's link: https://ls1tech.com/forums/parts-cla...-t56-swap.html
Installed but never ran MS4 cam. It was in a stock LS1 that was never finished beyond the shortblock after the cam was installed. Can include the stock 241 heads with BRAND NEW BTR .660 lift valve springs if desired.
$300 for MS4 only --SOLD--
$450 for the 241's with new BTR .660's
Text for pics.
Call/text (717) 377-6983
Last edited by 01blackbeast; 01-07-2014 at 09:22 PM.
09-19-2013, 06:59 AM
#2
Staging Lane
Thread Starter
iTrader: (41)
Join Date: Jul 2006
Location: Warfordsburg, Pa
Posts: 97
Likes: 0
Received 0 Likes
on
0 Posts
Turbo kit added. Just gauging interest. It's still on the car and I know I'll regret selling it if I do, but I'm thinking about going a different route or building a garage. Fairly firm on the price though as a result.
Last edited by 01blackbeast; 10-14-2013 at 07:19 PM.
Trending Topics
10-15-2013, 08:54 PM
#15
Staging Lane
Thread Starter
iTrader: (41)
Join Date: Jul 2006
Location: Warfordsburg, Pa
Posts: 97
Likes: 0
Received 0 Likes
on
0 Posts
PM sent on driveshaft and decided to list my whole complete setup.
I'll take 350 picked up or you pay the shipping.
I'll take 350 picked up or you pay the shipping.
Last edited by 01blackbeast; 01-01-2014 at 10:06 PM.
10-16-2013, 06:00 AM
#17
Staging Lane
Thread Starter
iTrader: (41)
Join Date: Jul 2006
Location: Warfordsburg, Pa
Posts: 97
Likes: 0
Received 0 Likes
on
0 Posts
^^^Sounds like a hijackrd. IMO. This is not a need to sell, but a "could use a garage or UTV more than these parts sale." Figured I would see if there were any contractors looking for work.
