SOLD! --Trick Flow LS1/LS2/LS6 fully CNC Ported heads $1500 shipped
01-20-2015, 10:35 PM
#1
SOLD! --Trick Flow LS1/LS2/LS6 fully CNC Ported heads $1500 shipped Category: Racing Parts
Price: $1699
Part Fits: 93-02 Chevrolet Camaro, 93-02 Pontiac Firebird, Corvette, 04-06 Pontiac GTO, 04+ Cadillac CTS-V
Location (State): PA
Item Condition: Used
Shipping Information: Item Can be Shipped
Engine: LS2/LS3/LS7/L92/LS9, LS1/LS6
LS Engine?: Fits LS Engine
$1,500 shipped takes them!
Like new Trick Flow 205cc cathedral port heads. Here's the story:
SOLD!
I picked them up a while back and they had very little run time on them. I took them apart, cleaned them, checked all the guides, checked the valve job, checked the springs, and had the heads cut to clean up some scratches and nicks that were in the gasket surface from being moved around and stored. We took .004" off to clean them up.
Guides, springs, and valve job were all like new. The ONLY issue that could be found with these heads was the scratches and nicks in the gasket surface, which has been cut clean. There was no warpage or evidence of over heating, just nicks and scratches.
I can't say how many miles were put on the heads, that is unknown, but they wouldn't come this clean if it were very many. The heads are ready to run, and in excellent working order.
Springs are set up for .600 lift.
Asking $1,699
Flow numbers:
Lift: Intake: Exhaust:
.100 66 52
.200 135 109
.300 203 165
.400 257 209
.500 287 222
.600 299 237
Here's a quote with some build specs and number produced by the same Trick Flow 205cc cylinder heads:
We just built a nice 5.3L engine using these 205 Trick Flow heads for a magazine project car.
Pretty impressed with the numbers. What we had:
TF 205 CNC heads
5.3L alum block
Stock 5.3 rods
Stock 5.3 crank
Stock 4.8L pistons (flat top)
LS2 intake (LS2 injectors)
Turn Key 90mm TB
TF 220/224 112LSA cam
stock lifters
Harland Sharp rockers
On the Superflow 901 dyno it made 491 hp at 6300 rpm and 444 tq at 4700 rpm. Those are corrected SAP numbers.
19 inches of vacuum at idle. I will get a dyno chart up in the next couple of days.
Pretty impressed with the numbers. What we had:
TF 205 CNC heads
5.3L alum block
Stock 5.3 rods
Stock 5.3 crank
Stock 4.8L pistons (flat top)
LS2 intake (LS2 injectors)
Turn Key 90mm TB
TF 220/224 112LSA cam
stock lifters
Harland Sharp rockers
On the Superflow 901 dyno it made 491 hp at 6300 rpm and 444 tq at 4700 rpm. Those are corrected SAP numbers.
19 inches of vacuum at idle. I will get a dyno chart up in the next couple of days.
Would take some items on partial trade such as:
-T56 needing repairs (LS)
-Nice headers for LS F body
-Intake manifold for LS3 (stock, Fast, etc
-TB (cable driven) for said manifold
-Speedline WS6 wheels
-Koni SA front shocks
-Strano lowering springs
-
Last edited by fergymoto; 02-07-2015 at 05:07 PM.
01-22-2015, 09:39 PM
#3
Admittedly I'm no longer in the market for heads but so few people know about how darn good these heads really are. They flow very well for a stock sized runner, they have the powdered metal valve guides so they are stock rocker arm compatible, and the small chambers and 13.5 degree valve angle work extremely well with larger camshafts.....high compression ratio and a lot of piston to valve clearance....good luck with the sale.
Trending Topics
02-06-2015, 12:00 PM
#10
If our dollar wasn't in the toilet right now I'd give u a decent offer. I want these heads but it's just to much with exchange/shipping right now.
Free bump for the heads I want lol
Free bump for the heads I want lol
