LQ9 6.0L L92 Fresh Built Forged internal Pan to Intake Never Run TEX T101A!
01-29-2015, 11:47 AM
#1
Teching In
Thread Starter
iTrader: (1)
Join Date: Nov 2013
Posts: 0
Likes: 0
Received 0 Likes
on
0 Posts
LQ9 6.0L L92 Fresh Built Forged internal Pan to Intake Never Run TEX T101A! Category: Engine - Complete Motors
Price: $1
Part Fits: 2010+ Camaro, 93-02 Chevrolet Camaro, 93-02 Pontiac Firebird, Corvette, 04-06 Pontiac GTO, 04+ Cadillac CTS-V, 67-92 Chevrolet Camaro, 67-92 Pontiac Firebird, Front wheel drive vehicles
Location (State): MD
Item Condition: Brand New
Engine: LS2/LS3/LS7/L92/LS9
LS Engine?: Fits LS Engine
PART OUT PRICING
Short block no pan - $2700
Heads - $700
Intake - $250
Fuel Rails - $150
Injectors - $100
Throttle - $50
Starter BNew - $50
Accessories with BNew Crank pulley - $500
oil pump - $100
rockers - $120
coils - $100
cam - $400
Mcleod twin plate with flywheel - $300
harness and PCM (DBC/85MM MAF) - $200
$5000 for all
Located in Hagerstown, MD
Built/Machined/Balanced by Gunther's Race Machine in Woodsboro, MD
Have all receipts and invoices!!
LQ9 6.0 block - .005 hone
LS3/L92 Heads - .030 milled, fluxed, rebuilt
TEX Racing T101A straight cut 4 speed dog box - fresh rebuild with Andrews Gears
11.5: 1 projected CR (still boostable)
Block
Wiseco +9cc Dome pistons
Gen IV Big Rods with APR bolts
Micropolished crank
Melling HP oil pump
Canton front sump pan for GTO / 240SX with dipstick and remote oil filter block
ZR1 Timing Chain
Pat G spec'd EPS grind cam 232/240 .629/.629 112 LSA +2
LS7 lifters
ZO6 Accessories as pictured. less that 40k miles
Heads
New Valves
Seats checked
New Valve Seals
.650 Lift sprints and Titanium retainers from AFR heads (brand new)
Comp Trunion Upgrade
LS3 Intake
102MM throttle with sensors
Billet BBK fuel rails
LS2 Injectors
starter
Mcleod Twin disk clutch used but still very usable
hydro Throwout bearing
bellhousing (motor sets assembled with trans and TO clearanced
05 Express Van harness and PCM.
Truck vented coils
All sensors
Needs valve covers (using dummies for protection)
Needs vent system (100 bucks)
Needs MAP sensor
ASKING $5,000 for Engine
ASKING $4,000 for Transmission
accepting offers at this time
PLEASE TEXT 2404526977
The transmission and machine work are worth close to that alone.
Last edited by ch1873857; 01-30-2015 at 09:45 AM.
01-30-2015, 09:46 AM
#2
Teching In
Thread Starter
iTrader: (1)
Join Date: Nov 2013
Posts: 0
Likes: 0
Received 0 Likes
on
0 Posts
bump for part out
UPDATE
PART OUT PRICING
Short block no pan - $2700
Heads - $700
Intake - $250
Fuel Rails - $150
Injectors - $100
Throttle - $50
Starter BNew - $50
Accessories with BNew Crank pulley - $500
oil pump - $100
rockers - $120
coils - $100
cam - $400
Mcleod twin plate with flywheel - $300
harness and PCM (DBC/85MM MAF) - $200
$5000 for all
UPDATE
PART OUT PRICING
Short block no pan - $2700
Heads - $700
Intake - $250
Fuel Rails - $150
Injectors - $100
Throttle - $50
Starter BNew - $50
Accessories with BNew Crank pulley - $500
oil pump - $100
rockers - $120
coils - $100
cam - $400
Mcleod twin plate with flywheel - $300
harness and PCM (DBC/85MM MAF) - $200
$5000 for all
01-31-2015, 09:13 PM
#5
Teching In
Thread Starter
iTrader: (1)
Join Date: Nov 2013
Posts: 0
Likes: 0
Received 0 Likes
on
0 Posts
Two guys messaging about the throttle. Its an eBay throttle I believe. I was told otherwise and paid too much money for it from someone on here. Slimy bastard. But don't worry I'm honest haha. Shoot me offers over text
