TH400 for your T56
#1
TECH Enthusiast
Thread Starter
Join Date: Mar 2002
Location: York, PA
Posts: 630
Likes: 0
Received 0 Likes
on
0 Posts
TH400 for your T56
My TH400 has about 250 break-in miles on it.. and I'm looking for someone to do an even swap. Not looking to pay extra. This tranny and converter alone are about 2k new. I need your working (not broke, aka not a I think it's ok but makes noise) T56 for an ATI TH400 w/ ATI torque ~3800 stall converter, pro shifter, and custom drive shaft, etc below.
Reason is I want to make my car less of a race car and more of a street car for better saleability. Plus I have some supras in the area that need to get some spankings... need that 5th 'n 6th.
I will however also consider built and functioning 4L8xe w/ converter.
Things I need from you:
Basically everything to make the tranny work if you have it.
Flywheel (if you have it)
T56 w/ bellhousing
drive shaft
M6 Tranny mount
Pedal assembly with clutch rod and brake rod clips
shifter pressure plate
shift linkage, shifter, upper/lower boots, etc.
master/slave hydraulics w/ mounting hardware (ubolts)
and all other related bolts
(I'm going with aftermarket clutch/pp and flywheel but would like those as well if you have them)
Things you get from me:
1330 yoke driveshaft shop drive shaft
ATI TH400 Race tranny w/ plugnplay speed sensor reluctor.
ATI Custom built Comp. Torque converter
ATI SFi flex plate w/ ARP bolts
B&M Pro shifter (manual reverse, with pull up reverse lock.. best design imo) and linkage
Custom Stainless Tranny Dipstick Tube
Pre-welded bung in pan for included 2 5/8 tranny temp gauge (autometer procomp)
Custom modified tranny mount to fit TH400.
all related bolts you need.
3 jugs of atf
Would prefer a local yokal.
Reason is I want to make my car less of a race car and more of a street car for better saleability. Plus I have some supras in the area that need to get some spankings... need that 5th 'n 6th.
I will however also consider built and functioning 4L8xe w/ converter.
Things I need from you:
Basically everything to make the tranny work if you have it.
Flywheel (if you have it)
T56 w/ bellhousing
drive shaft
M6 Tranny mount
Pedal assembly with clutch rod and brake rod clips
shifter pressure plate
shift linkage, shifter, upper/lower boots, etc.
master/slave hydraulics w/ mounting hardware (ubolts)
and all other related bolts
(I'm going with aftermarket clutch/pp and flywheel but would like those as well if you have them)
Things you get from me:
1330 yoke driveshaft shop drive shaft
ATI TH400 Race tranny w/ plugnplay speed sensor reluctor.
ATI Custom built Comp. Torque converter
ATI SFi flex plate w/ ARP bolts
B&M Pro shifter (manual reverse, with pull up reverse lock.. best design imo) and linkage
Custom Stainless Tranny Dipstick Tube
Pre-welded bung in pan for included 2 5/8 tranny temp gauge (autometer procomp)
Custom modified tranny mount to fit TH400.
all related bolts you need.
3 jugs of atf
Would prefer a local yokal.
#3
Restricted User
iTrader: (17)
I need everything but the driveshaft and the tranny.
I have an MN12 (GTO/Vette T56 with the cone syncros between 2-3 and 3-4 and more agressive gearing) with about 24K stock power GTO miles. Spec 5 clutch. Spec Steel flywheel. 6 month old hydraulics. Pro 5.0 shifter. Grey console. Stock crossmember. Poly mount.
PM me if you can get rid of the Tranny and driveshaft and we can work something out.
I have an MN12 (GTO/Vette T56 with the cone syncros between 2-3 and 3-4 and more agressive gearing) with about 24K stock power GTO miles. Spec 5 clutch. Spec Steel flywheel. 6 month old hydraulics. Pro 5.0 shifter. Grey console. Stock crossmember. Poly mount.
PM me if you can get rid of the Tranny and driveshaft and we can work something out.
#5
TECH Resident
iTrader: (64)
Join Date: Jul 2005
Location: sneaking in your back door as you leave!/cartersville ga
Posts: 908
Likes: 0
Received 0 Likes
on
0 Posts
i have it all also. flywheel needs turned or it may be useless. clutch pedal assembly , have all hydraulics. i jut switched to a 400, but it never hurts to have a extra one lying around.
#7
TECH Enthusiast
Thread Starter
Join Date: Mar 2002
Location: York, PA
Posts: 630
Likes: 0
Received 0 Likes
on
0 Posts
hey guys, I posted on a local easternfbody.com and got a call this a.m. from a local shop who has a customer willing to trade out, so I will be doing this locally. thanks for your interest!
-Rob
-Rob