Forged 408, moser, suspension, z06 parts, 4" exhsust, bmr
07-18-2016, 09:24 AM
#1
10 Second Club
Thread Starter
iTrader: (3)
Join Date: Aug 2007
Posts: 73
Likes: 0
Received 0 Likes
on
0 Posts
Forged 408, moser, suspension, z06 parts, 4" exhsust, bmr Category: Accessories
Price: $1000
Part Fits: 2010+ Camaro, 93-02 Chevrolet Camaro, 93-02 Pontiac Firebird, Corvette
Location (State): WI
Item Condition: Brand New
Shipping Information: Item Can be Shipped
Engine: LS2/LS3/LS7/L92/LS9, LS1/LS6, LT1/LT4
LS Engine?: Fits LS Engine
sold Fresh LQ9 408
Callie's compstar, 10/10 crank
Compstar rods 6.125
Dished JE pistons
Total seal rings
Arp 2000 rod bolts
New GM lsx main bolts
Hone
Align hone
Rebuild has 0 miles. Work done by Advanced Engine concepts from Green Lake wi.
Compression was 9to1 with my ls9 heads.
58 wheel. Can have ur 24 wheel installed for 50$
Will ship. Selling due to building a new 427 lsx.
gen3 but is machined for gen 4 knock sensors also. it was in my 10 camaro.
4300$ OBO
COMP Cams 7609-16 - Comp Cams Magnum Pushrods
Maybe 10k miles
7.300''
60$ OBO
SOLDMoser 12 bolt rear end, used
4th gen F-body
20k miles, Very little wine around 50 mph (just like most other moser’s)
Only selling this bc I parted out another car I had that had. It had a moser with 373’s that was a better fit for me so this one has to go.
410 gears
Auburn limited slip
Bolt in axle (does not come with plates, u use the ones off your old rear end)
33 spline axles
For abs, it came off my 2000 Camaro z28 so whatever that has is what it has. (at work right now so can’t go look. I thing 4)
Standard size wheel studs
Moser performance girdle cover
Standard axle length
B4 install it needs new outer axle bearings and oil installed. About 65$ for bearings or cheaper from parts local parts store
2200$ OBO
SPOHN Heavy duty Extreme Pro-Series Torque Arm, used
With front loop
12 bolt mount
Long tube header style mount
Was 645$ NEW
SOLDSPHOHN standard duty torque arm, used
Poly mount
With front loop
12 bolt mount
Was 435$ new
Hotchkis lower boxed control arms, used
Poly ends
Was 324 new
225$ OBO
4” Exhaust system w/magna flow muffler, Electric cut out, used
Dual tip single side exhaust
Fits perfect
Not sure on brand
Best exhaust tone ive ever heard
NEW WAS:
Pipe kit 440$
Magnaflow muffler 140$
Electric cut out and cut out pipe 220$
4” to dual 3” Y pipe with SS tips 85$
625$ OBO (this is not cut yet, so if shipped it will have to be cut once. Buyer can let me know where to cut)
Rear 22.4 MM sway bar, used
4th gen F-body (may fit 3rd gen)
Brand unknown (umi or bmr I think)
115.00$ OBO
T56 LT1 front cover, used
Taken off a lt1 trans to install LS1 cover
110$ OBO
Stock Z06 LS7 intake 22k mile, used
No rails or TB
275$ OBO
Stock 2007 c6 Z06 cat back exhaust 22k miles, used
150 OBO
2007 Red Z06 engine covers
120 OBO
Last edited by blown383z28; 08-29-2016 at 05:01 AM.
