Moser 9" inch WaveTrack and Nodular iron case FS/or trade for Spool Aluminum center
03-19-2017, 07:40 PM
#1
Moser 9" inch WaveTrack and Nodular iron case FS/or trade for Spool Aluminum center Category: Accessories
Price: $1100
Part Fits: 2010+ Camaro, 93-02 Chevrolet Camaro, 93-02 Pontiac Firebird, Corvette, 04-06 Pontiac GTO, 04+ Cadillac CTS-V, 67-92 Chevrolet Camaro, 67-92 Pontiac Firebird
Location (State): PA
Item Condition: Brand New
Shipping Information: Item Can be Shipped
Engine: LS2/LS3/LS7/L92/LS9, LS1/LS6, Small Block, Big Block
LS Engine?: Fits LS Engine
Or sell for $1100
Moser Nodualr iron center section
Moser 3.70 gears
Daytona billet aluminum front bearing support
Moser wavetrack 35 spline diff
Billet front 1350 yoke. Ready to bolt it!
4102181620
Last edited by yoshgixxer; 03-20-2017 at 08:53 PM.
03-19-2017, 09:31 PM
#2
Staging Lane
iTrader: (14)
Join Date: Aug 2005
Location: Kentucky
Posts: 59
Likes: 0
Received 0 Likes
on
0 Posts
Well I had a Wavetrac but sold it because I was afraid it wouldn't hold up to transbrake launches (700whp I hope). So I bought a Strange iron center with 3.89's and spool 35 spline.
Car isn't done but I wonder if the spool on the street will get on my nerves. Had one before and I didn't like it. Plus, a 3.70 would be more street friendly with the th400 possibly. Hmmm, I might be interested in a trade. Would you?
Car isn't done but I wonder if the spool on the street will get on my nerves. Had one before and I didn't like it. Plus, a 3.70 would be more street friendly with the th400 possibly. Hmmm, I might be interested in a trade. Would you?
03-20-2017, 07:37 AM
#3
Really looking for a aluminum center, I think a wavetrack will hold up to 700hp fine. And a spool does suck on the street. My cars 95% track so not worried about it, trying to cut weight out of the car. I really want a aluminum center for that very reason.
If I was staying iron I'd just sell the wavetrack for $6-700 and buy a $200 spool
If I was staying iron I'd just sell the wavetrack for $6-700 and buy a $200 spool
Trending Topics
03-21-2017, 07:28 PM
#8
Teching In
iTrader: (1)
Join Date: Nov 2015
Location: Bardstown, KY
Posts: 26
Likes: 0
Received 0 Likes
on
0 Posts
Building a fox /ls thinking powerglide 60/40 strip street.....does this setup not work with a trans Brake? Would this be good for me? Looking for help to finish part shopping.thanks
03-22-2017, 07:25 AM
#10
cars just going through a major weight loss program and never gets any street time so no need for a diff.
03-22-2017, 10:51 AM
#15
I have a really similar setup in my car:
Moser Nodular iron center section
3.25 gears
front bearing support
Moser wavetrack 35 spline diff
Billet front 1350 yoke.
I have made 1240hp to the tire and my timeslips (1.26 60' with 8.30 ET @ over 3600lbs) match this on Wallace Racing Calculator. I have not had an issue to this point. I have somewhere around 6000 miles on my rear with everything from 575hp - 1240hp.
Stout equipment. Caught my eye because I am consider a similar swap. Good luck with sale (keeping my eye on this for future reference).
Moser Nodular iron center section
3.25 gears
front bearing support
Moser wavetrack 35 spline diff
Billet front 1350 yoke.
I have made 1240hp to the tire and my timeslips (1.26 60' with 8.30 ET @ over 3600lbs) match this on Wallace Racing Calculator. I have not had an issue to this point. I have somewhere around 6000 miles on my rear with everything from 575hp - 1240hp.
Stout equipment. Caught my eye because I am consider a similar swap. Good luck with sale (keeping my eye on this for future reference).