9.80's first weekend out - LS1TECH

Log In 


Single Digit Club Running 9s or quicker? Damn!

9.80's first weekend out

Reply
 
Thread Tools Search this Thread
Old 10-13-2010, 03:50 PM   #1
Staging Lane
Thread Starter
 
slooter's Avatar
 
Join Date: Jun 2008
Location: Burford Ontario
Posts: 70
Default 9.80's first weekend out

Right now I have a 368 800 hp N/A motor,1st time out ran a 9.80's at 140mph....... 3300 lb car with driver.I have a few issues
with gear and converter,but we will figger that out one step at a time.
I was going to build another short block but a larger cubs 412,or a 420 something square like that.
I would like to run in the 8.70 range,10.5 tire.




Thanks for looking

Tony : )
slooter is offline   Reply With Quote
Old 10-13-2010, 06:58 PM   #2
TECH Enthusiast
iTrader: (6)
 
billyflantos's Avatar
 
Join Date: Aug 2008
Location: DAVIDSON NC
Posts: 571
Default

good looking car...
billyflantos is offline   Reply With Quote
Old 10-13-2010, 10:37 PM   #3
On The Tree
iTrader: (22)
 
highpockets's Avatar
 
Join Date: Apr 2004
Posts: 198
Default

Nice job hanging the front wheels too ! Wish mine would do that just once,damn that IRS !
highpockets is offline   Reply With Quote
Old 10-15-2010, 08:31 PM   #4
Launching!
iTrader: (6)
 
Join Date: Aug 2008
Location: Waco, Tx
Posts: 265
Default

Badass lookin car man! There is alot more left in that setup, any specs on the engine? My 364" LS2 is about done, going the N/A route as well
casper383 is offline   Reply With Quote
Old 10-16-2010, 09:08 AM   #5
Staging Lane
Thread Starter
 
slooter's Avatar
 
Join Date: Jun 2008
Location: Burford Ontario
Posts: 70
Default

Quote:
Originally Posted by casper383 View Post
Badass lookin car man! There is alot more left in that setup, any specs on the engine? My 364" LS2 is about done, going the N/A route as well
Hey Casper383 thanks for the good words.

368 sbc
SB2.2 Heads, titanium valves,Jessel rockers
Bowtie block with roller cam bearings
Custom built cam ,solid roller,
custom JE pistons
GRP Alumium rods
Custom COLA billet crank
aprox 14.5 to 15 to 1 compression
Belt drive oil system
Thats just off the top of my head.........?
I had LS motor in my car before,was new .....after 50 passes
put a rod out the side of the alumium block..... : (
Decided to go 1st gen stuff,parts a lot cheaper,and easier to get.

Good luck with your new combo,nice car too...... : )

Tony
slooter is offline   Reply With Quote
Old 10-16-2010, 11:46 AM   #6
Staging Lane
Thread Starter
 
slooter's Avatar
 
Join Date: Jun 2008
Location: Burford Ontario
Posts: 70
Default

Here's my first 9sec pass
Sorry about the burnout I think it was the water boy first day,
he couldn't even get me in the water...... : (
Enjoy.................... ; )

Tony

http://www.youtube.com/watch?v=7rreYQnL_e0
slooter is offline   Reply With Quote
Old 10-16-2010, 08:02 PM   #7
Launching!
iTrader: (6)
 
Join Date: Aug 2008
Location: Waco, Tx
Posts: 265
Default

Damn that car leaves nice, motor sounds wicked! What was the 60ft on that pass? Keep us posted when you get some more E.T knocked off, good luck with it.
casper383 is offline   Reply With Quote
Old 10-18-2010, 10:01 AM   #8
Staging Lane
Thread Starter
 
slooter's Avatar
 
Join Date: Jun 2008
Location: Burford Ontario
Posts: 70
Default

Quote:
Originally Posted by casper383 View Post
Damn that car leaves nice, motor sounds wicked! What was the 60ft on that pass? Keep us posted when you get some more E.T knocked off, good luck with it.
The 60ft was only 1.38.....like you said there's alot in it still
slooter is offline   Reply With Quote
Old 10-21-2010, 07:08 AM   #9
Staging Lane
Thread Starter
 
slooter's Avatar
 
Join Date: Jun 2008
Location: Burford Ontario
Posts: 70
Default 9 sec club

Could I be added to the 9sec club

Thanks Tony...... ; )
slooter is offline   Reply With Quote
Old 12-03-2010, 03:21 PM   #10
Staging Lane
Thread Starter
 
slooter's Avatar
 
Join Date: Jun 2008
Location: Burford Ontario
Posts: 70
Default 9 sec club

How to get in the 9 sec club...............

Tony
slooter is offline   Reply With Quote
Old 01-14-2011, 09:34 AM   #11
Staging Lane
Thread Starter
 
slooter's Avatar
 
Join Date: Jun 2008
Location: Burford Ontario
Posts: 70
Default 9 sec

A few changes this year..................

Change rear gear from 4.10 to 4.86
Change converter from 5500 stall to 6800 stall
narrow rear end 2in on each side,get lower center
wheelie bar.........just a small one
Fine tune engine on dyno.......get best tune.

should get me in 9.30's don't u think

Tony......
slooter is offline   Reply With Quote
Old 01-27-2011, 03:57 PM   #12
RJE
Teching In
 
Join Date: Nov 2009
Location: NC
Posts: 45
Default

Nice car, and nice times!! Once you get everything sorted out you will really be flying. I hope to make some 9 sec passes this spring.

Randy
RJE is offline   Reply With Quote
Old 01-27-2011, 11:31 PM   #13
Launching!
 
Turbo-T's Avatar
 
Join Date: Mar 2006
Location: Bladenboro, N.C.
Posts: 212
Default

all i can say maybe the ford needs to give you the chute and the bars because when you left him all he could do was dream!
Turbo-T is offline   Reply With Quote
Old 01-29-2011, 06:01 PM   #14
8 Second Club
iTrader: (26)
 
Firehawk441's Avatar
 
Join Date: May 2005
Location: 8.50 INDEX RACING
Posts: 1,900
Default

Quote:
Originally Posted by slooter View Post
Hey Casper383 thanks for the good words.

368 sbc
SB2.2 Heads, titanium valves,Jessel rockers
Bowtie block with roller cam bearings
Custom built cam ,solid roller,
custom JE pistons
GRP Alumium rods
Custom COLA billet crank
aprox 14.5 to 15 to 1 compression
Belt drive oil system


Tony
Nice combo... Who did the SB2.2 heads for you?
Firehawk441 is offline   Reply With Quote
Reply


Tags
572, 785hp, big, block, camaro, casper383, chevy, duramax, engine, ls1tech, ls2, sb22, valves, wicked, youtube

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are Off



All times are GMT -5. The time now is 08:36 PM.