Bcm
11-29-2008, 12:43 PM
#1
Staging Lane
Thread Starter
iTrader: (5)
Join Date: Aug 2008
Posts: 83
Likes: 0
Received 0 Likes
on
0 Posts
Bcm I know this has been answered before. I for some reason cannot find the answer i'm looking for.
I have installed a remote start in my 98 formula and want to know how I can bypass the bcm or give it always on power. I have tried the bcm wake fix but its not working. Any help would be great!
I have installed a remote start in my 98 formula and want to know how I can bypass the bcm or give it always on power. I have tried the bcm wake fix but its not working. Any help would be great!
11-29-2008, 08:12 PM
#2
TECH Addict
iTrader: (1)
Join Date: Nov 2007
Location: Narnia
Posts: 2,372
Likes: 0
Received 0 Likes
on
0 Posts
What problem are you having with the remote start?
PM me if you want any remote start info. I did mine a little while back, and know quite a bit about alarm installation.
PM me if you want any remote start info. I did mine a little while back, and know quite a bit about alarm installation.
12-05-2008, 04:48 PM
#4
Staging Lane
Thread Starter
iTrader: (5)
Join Date: Aug 2008
Posts: 83
Likes: 0
Received 0 Likes
on
0 Posts
After the bcm goes to sleep I cannot unlock my doors with the aftermarket unit. The factory still works fine. I have been remote starting the car, then unlocking the doors with the aftermarket unit with no issue.
12-12-2008, 09:58 AM
#5
Teching In
Join Date: Aug 2008
Posts: 10
Likes: 0
Received 0 Likes
on
0 Posts
im having a simalar problem,,,it seem as though im not getting a signal to the ''bcm'',,i dont know if my contacts are bad in the ignition switch or not,,ive tried new keys,,and my security light flashes, but does not turn off
tried to bypass vats but no luck
i had my local ls1 guru,to try it and he says that i didnt havr a signal,,,,is there a way to replace the bcm,,,or will i have to take it to the stealership,,,,,,,any info ??
tried to bypass vats but no luck
i had my local ls1 guru,to try it and he says that i didnt havr a signal,,,,is there a way to replace the bcm,,,or will i have to take it to the stealership,,,,,,,any info ??
Last edited by WhiteBird00; 12-12-2008 at 10:45 PM. Reason: multiple consecutive posts
12-12-2008, 01:22 PM
#6
TECH Resident
iTrader: (9)
Join Date: Dec 2005
Location: San Jose, CA
Posts: 982
Likes: 0
Received 0 Likes
on
0 Posts
http://www.bfranker.badz28.com/fbody/alarm96up3.htm
go to the door locks section, everything you need to know is there.
go to the door locks section, everything you need to know is there.
Trending Topics
12-12-2008, 03:23 PM
#8
Staging Lane
Thread Starter
iTrader: (5)
Join Date: Aug 2008
Posts: 83
Likes: 0
Received 0 Likes
on
0 Posts
locks http://www.bfranker.badz28.com/fbody/alarm96up3.htm
go to the door locks section, everything you need to know is there.
go to the door locks section, everything you need to know is there.
12-12-2008, 10:48 PM
#9
Your best bet is to go back and check it again. Since your factory remote still works properly, there is nothing wrong with the BCM. Therefore, the added aftermarket unit and/or its wiring must be the source of the problem.
For example, the BCM has multiple wires of the same color. Perhaps you made a connection to the right color but wrong wire.
For example, the BCM has multiple wires of the same color. Perhaps you made a connection to the right color but wrong wire.
