0015 - LS1TECH - Camaro and Firebird Forum Discussion - Threads Tagged with 0015

LS1TECH - Camaro and Firebird Forum Discussion
Tags
Threads Tagged with 0015

Threads Tagged with 0015

Thread / Thread Starter

Last Post

Replies

Views

Forum

0015, 67, aframe, bolt, bottoming, camaro, gas, handle, hole, hurst, ls1, pedal, rockauto, shifter, spacing, swap, tubular

1 Attachment(s)

Old School LSx 1967 Camaro

(

Multi-page thread

1 2 3 4 5 ... Last Page)

67rally on 12-12-2013

07-30-2015 09:05 PM
by 95 Stang

Go to last post

48,074

Conversions & Swaps

0015, accurate, bearing, bearings, build, clearance, crank, eagle, engine, plastigage, rod, tight

Is .0015 measured with platigage too tight for a rod bearing clearance?

FastKat on 05-04-2014

05-08-2014 11:29 AM
by crossbreed383

Go to last post

12

18,279

Generation IV Internal Engine

0015, 002, 350, bearing, cb663hn, clearance, difference, journal, micrometer, motor, oil, race, rod, rods, sbc, throw, tighter, vs0025

Rod bearing clearance between .0015 and .002 too tight?

kgkern01 on 05-09-2013

05-15-2013 03:32 PM
by fex77k

Go to last post

17

19,942

LT1-LT4 Modifications

0015, 04, 25, 53, 53l, 925, bolt, head, heads, ls1tech, milled, prc, ready, sale, stage

6 Attachment(s)

PRC Stage 2.5 5.3L Heads, ready to bolt on

(

Multi-page thread

1 2)

1994B4C on 04-17-2012

05-08-2012 08:25 PM
by 1994B4C

Go to last post

26

3,453

Parts Classifieds

001, 0015, bc409jstd, bearing, bearings, clearance, clevite, engine, ls1, main, ms2199, shape, tech, tight, undersize

.0015"-.0018" main bearing clearance - iron block

91 240 on 04-01-2012

05-05-2012 08:49 AM
by 2000RATA

Go to last post

13

34,338

Forced Induction

0015, 77, bbc, bearing, bearings, crank, gage, high, instructions, plastigage, plastigauge, plastiguage, reads, rod, sbc, tolerances

rod bearing plastigage help?

ezrollin on 07-19-2006

02-20-2008 10:05 PM
by m6ls1maro

Go to last post

18

12,999

Advanced Engineering Tech

0015, 53l, bearing, bearings, clearance, gm, high, idle, ls1, main, mustang, oil, pressure, rod, tight

bearing clearances too tight?

sroka on 08-24-2007

08-27-2007 08:50 PM
by SLED28

Go to last post

19

9,581

Generation III Internal Engine

0015, 2009, compression, duramax, head, heads, ktm, milled, xc

Question about Milled heads?

KWIKKAR on 05-30-2007

05-30-2007 10:00 PM
by KWIKKAR

Go to last post

2

497

Forced Induction

0015, 015, 030, 050, 1486, 243, 53, base, circle, heads, length, milled, push, pushrod, pushrods, rod, shorter

What pushrod length with 1.486 base circle and 5.3 heads milled .015

TRYMYZ on 04-19-2006

04-19-2006 02:30 PM
by TRYMYZ

Go to last post

4

588

Generation III Internal Engine

All times are GMT -5. The time now is 10:31 PM.