*********01 NBM Formula shop/personal car for sale*******
#1
FormerVendor
Thread Starter
iTrader: (39)
Join Date: Apr 2004
Location: Tomball, Tx
Posts: 1,243
Likes: 0
Received 0 Likes
on
0 Posts
*********01 NBM Formula shop/personal car for sale*******
453 rwhp 2001 M6 Formula with 86xxx miles on her. Charcoal gray cloth interior. The car has been well kept and I am the second owner. There is a scratch here and there but no dings or anything of that sort. Inside and outside are very clean!!!
Brief mods list. "I know I will forget some allot".
-All side and rear lights tinted black
-Zo6 motorsports wheels. 305/35/18 nitto drags out back with 275/40/17's up front
-Pavlock Performance heads flow 322cfm with patriot extremes/titanuim retainers.
-TR CM pushrods
-Trex cam
-full bolt ons
-strange 12 bolt with spool 3:73 gears
-Fully NHRA legal studs on all four corners
-Pavlock Performance PHB and LCA's in polished finish
-Bmr torque arm with fabbed 1/2 inch rear plate that mounts to rear end housing. vs. 1/4 inch plate.
-Torque arm relocation bracket/ trans cross member
-Drive shaft safety loop
-Sub frame connectors
-Walbro 255
-1le springs
-Auto meter shift light
-B&M Ripper shifter shortened
-4'' outlaw ws6 lift off hood
Ill add more to the list when I remember all the small details.
Looking for 16k obo. with everything mentioned above!!
Bryan
Brief mods list. "I know I will forget some allot".
-All side and rear lights tinted black
-Zo6 motorsports wheels. 305/35/18 nitto drags out back with 275/40/17's up front
-Pavlock Performance heads flow 322cfm with patriot extremes/titanuim retainers.
-TR CM pushrods
-Trex cam
-full bolt ons
-strange 12 bolt with spool 3:73 gears
-Fully NHRA legal studs on all four corners
-Pavlock Performance PHB and LCA's in polished finish
-Bmr torque arm with fabbed 1/2 inch rear plate that mounts to rear end housing. vs. 1/4 inch plate.
-Torque arm relocation bracket/ trans cross member
-Drive shaft safety loop
-Sub frame connectors
-Walbro 255
-1le springs
-Auto meter shift light
-B&M Ripper shifter shortened
-4'' outlaw ws6 lift off hood
Ill add more to the list when I remember all the small details.
Looking for 16k obo. with everything mentioned above!!
Bryan
Last edited by Pavlock Performance; 04-28-2008 at 12:34 AM.
#2
TECH Fanatic
iTrader: (12)
Join Date: Nov 2001
Location: The Woodlands, TX
Posts: 1,934
Likes: 0
Received 0 Likes
on
0 Posts
I sure hope my baby goes to a good home.
This car has been a beast its entire life. Went 13.0's bone stock in 95 degree weather. It was also the FIRST bolt-on car to trap over 120mph
#3
FormerVendor
Thread Starter
iTrader: (39)
Join Date: Apr 2004
Location: Tomball, Tx
Posts: 1,243
Likes: 0
Received 0 Likes
on
0 Posts
The car is very stout! I feel for all of the mods this car has, and all of the EXTRA parts that are givin with the car, this is a very good deal!
You are givin a full complete set of drag wheels/tires.
Brand new pin on hood with mounting acc.
Exhaust is all interchangeable from REALLY loud, to loud, to barely hear it idle!
It has two cut outs directly behind the headers, than comes the y-pipe to 4'' I pipe with 4'' bullet muffler than again 4'' pipe all the way back behind the axle. Than you can bolt my stock ws6 muffler with 4'' flange welded to it, or if BADHABITBIRD doesnt buy my other mufflex/spintech catback, this will be offered with the car as well!
Sean you better buy it soon lol
You are givin a full complete set of drag wheels/tires.
Brand new pin on hood with mounting acc.
Exhaust is all interchangeable from REALLY loud, to loud, to barely hear it idle!
It has two cut outs directly behind the headers, than comes the y-pipe to 4'' I pipe with 4'' bullet muffler than again 4'' pipe all the way back behind the axle. Than you can bolt my stock ws6 muffler with 4'' flange welded to it, or if BADHABITBIRD doesnt buy my other mufflex/spintech catback, this will be offered with the car as well!
Sean you better buy it soon lol
Trending Topics
#8
FormerVendor
Thread Starter
iTrader: (39)
Join Date: Apr 2004
Location: Tomball, Tx
Posts: 1,243
Likes: 0
Received 0 Likes
on
0 Posts
It ran a 11.48 I believe cam only. Now went with this bigger cam and heads. Took it to baytown about a month or so ago which is the pic at the very top. Ran it with the nittos and it couldnt hook up due to all the oil everyone was throwing all over the track. it ran a 11.5 @ 124 gaining traction in 4th gear. I don't see why it wouldn't run 10's considering It was not a clean pass what so ever.