SOLD - 86 s10 super sleeper 4.8L/t56 cam and blower. Must watch video!!
#1
9 Second Club
Thread Starter
iTrader: (10)
Join Date: Oct 2008
Location: orion, IL
Posts: 173
Likes: 0
Received 0 Likes
on
0 Posts
SOLD - 86 s10 super sleeper 4.8L/t56 cam and blower. Must watch video!!
Year: 1986
Make: Chevrolet
Model: S-10
Price: $8000
Mileage: 300000
Private or Dealer Listing: Private Listing
Location (State): IL
Color: Red
Transmission: Manual
Drivetrain: Rear Wheel Drive
LS Engine?: Car has LS engine
I think we will start of with a video to get you interested!
Truck drives great and gets decent fuel mileage. I would trust it to drive anywhere. Also took it on powertour this year and was shown in hotrod magazine! This truck sounds crazy awesome with the blower and will definately get some attention!
Engine:
4.8L (1xx, xxx miles)
Cam (I'll have to look up the specs)
Patriot dual springs
Hardened pushrods
Cut down truck pan
Custom intake setup to bolt on a lightning blower
Blower ported by stagmeier (~14psi)
Shorty headers
Single 3" exhaust out the back
Exhaust cutout
60 lb injectors
Walbro 255 in tank pump
Aftermarket rails and adjustable fuel pressure regulator
2 bar map sd tuned
tuned with low timing for 93 octane
Intake has meth spray bar built in (2 4gpm nozzles but no meth kit on the truck
Transmission:
01 camaro t56 30k miles on a rebuild
LS7 clutch
LS2 flywheel
Rear end:
Stock s10 rear (I think 3.42 gear)
Suspension:
1" belltech front drop springs
2" drop spindles
4" rear drop block
Brand new steering linkage and steering box
New ball joints
New a arm bushings
New shocks on all corners
Interior:
Digital dash conversion (all gauges work, 6k tach)
Blue tooth stereo
A/f gauge in glove box
Blazer buckets
cb radio (for powertour)
Good heat
No a/c
Exterior:
Ladder rack (for the sleeper look
grandpa bug shield
Stock wheels with brand new tires (235s)
Also comes with 2 extra rear wheels with 235 et streets
The bad:
Motor mounts need replaced, they were stock rubber mounts and the rubber is torn. They are clam shell style so the engine can't go anywhere but they should be replaced.
Driver side front fender has been replaced and needs the silver stripe painted on it
Other than that the engine bay could use a little clean up and the blower motor resistor needs to have the connector swapped on it so it can plug in (heat only works on high)
I also made brackets to use the 4.3 a/c compressor on the ls engine and have the a/c box and condenser. Basically everything to make the a/c work that will come with the truck.
SOLD
Last edited by thirdgen60; 12-20-2014 at 03:19 PM.
Trending Topics
#16
Teching In
iTrader: (3)
Join Date: Jun 2012
Location: NW suburbs Chicago
Posts: 35
Likes: 0
Received 0 Likes
on
0 Posts
Got you posted to Bring a Trailer. Hopefully it helps. This build is really cool.
Although they did get the motor wrong.
http://bringatrailer.com/2014/12/12/...1-and-6-speed/
Although they did get the motor wrong.
http://bringatrailer.com/2014/12/12/...1-and-6-speed/
#17
9 Second Club
Thread Starter
iTrader: (10)
Join Date: Oct 2008
Location: orion, IL
Posts: 173
Likes: 0
Received 0 Likes
on
0 Posts
Haha thanks man. I got a couple messages from guys off of bring you trailer and I was like wtf is bring your trailer lol.
Also updated some info and a walkaround video.
Looottts of interest, no cash in hand yet. So you still have a chance a buy this machine!
Also updated some info and a walkaround video.
Looottts of interest, no cash in hand yet. So you still have a chance a buy this machine!
#18
Yea Ill bet theres been crazy interest. This darn thing is driving me crazy right now.