In AZ, Good with Car Audio and want an LS1 Driveshaft for your time? Come in
06-02-2009, 11:25 PM
#1
12 Second Club
Thread Starter
iTrader: (10)
Join Date: Nov 2007
Location: Tucson, AZ
Posts: 1,095
Likes: 0
Received 0 Likes
on
0 Posts
In AZ, Good with Car Audio and want an LS1 Driveshaft for your time? Come in Heres the thread, I am sick of it I have better things to work on involving go fast items this is just pissing me off.
If your local and want an LS1 Driveshaft I will give it to your for doing all the wiring from the nightmare I got from someone else. I am pissed and I have a lot of other items to put on.
https://ls1tech.com/forums/stereo-el...l#post11695817
If your local and want an LS1 Driveshaft I will give it to your for doing all the wiring from the nightmare I got from someone else. I am pissed and I have a lot of other items to put on.
https://ls1tech.com/forums/stereo-el...l#post11695817
06-02-2009, 11:48 PM
#2
TECH Addict
iTrader: (3)
Join Date: Oct 2007
Location: Orange County
Posts: 2,543
Likes: 0
Received 0 Likes
on
0 Posts
damn that sucks. what i did with my stereo, is i discarded all the stock speaker wiring, re-ran speaker wire from each speaker to an amp in the back, then ran the amp to my headunit with an rca connection. very simple and sounds great.
06-03-2009, 12:32 AM
#5
12 Second Club
Thread Starter
iTrader: (10)
Join Date: Nov 2007
Location: Tucson, AZ
Posts: 1,095
Likes: 0
Received 0 Likes
on
0 Posts
I think I killed them both somehow because I just tried turning one on by connecting it right to the battery and no power at all... I have no clue how speaker wiring could do it... but sounds like my luck.
Trending Topics
06-03-2009, 01:43 AM
#9
12 Second Club
Thread Starter
iTrader: (10)
Join Date: Nov 2007
Location: Tucson, AZ
Posts: 1,095
Likes: 0
Received 0 Likes
on
0 Posts
No I mean I picked up one of my car batterys laying around and put the CD Players ground to ground and power to Positive and nothing.
However on an odd note I went back out to the car to play around some more and the radio in it turned on...
I have noticed something strange, when the radio is connected and working my wideband goes from reading 20.0 for the car not being started to reading (Getting to 15.3).... I disconnected it this time I do not want to fry the deck (The other may be fine, I took it apart and could not find any problems on the board. I hope not I liked that deck planned on putting it in my new Daily Driver).
I have no idea what to make of this but I think the Bose Setup is to blame for it. I have been searching here with no luck so I will make a thread asking:
How the hell do you remove the Bose pieces are they just the items connected directly to the Speakers or is there more... I believe more since it requires me to connect the remote line and there is another orange/white stripe wire I have no idea about.
Where is it I will pull it out.
Either way though looks like I need to rewire the whole car.
I will give the Driveshaft still to anyone who wants to do this for me.
However on an odd note I went back out to the car to play around some more and the radio in it turned on...
I have noticed something strange, when the radio is connected and working my wideband goes from reading 20.0 for the car not being started to reading (Getting to 15.3).... I disconnected it this time I do not want to fry the deck (The other may be fine, I took it apart and could not find any problems on the board. I hope not I liked that deck planned on putting it in my new Daily Driver).
I have no idea what to make of this but I think the Bose Setup is to blame for it. I have been searching here with no luck so I will make a thread asking:
How the hell do you remove the Bose pieces are they just the items connected directly to the Speakers or is there more... I believe more since it requires me to connect the remote line and there is another orange/white stripe wire I have no idea about.
Where is it I will pull it out.
Either way though looks like I need to rewire the whole car.
I will give the Driveshaft still to anyone who wants to do this for me.
06-04-2009, 12:45 AM
#12
TECH Resident
iTrader: (13)
Join Date: Nov 2005
Location: west phx
Posts: 782
Likes: 0
Received 0 Likes
on
0 Posts
i would do look into it for you but geeez man your way the f out there lol
i live in w phoenix avondale/goodyear area
if you come up to phx we could probably work something out
i live in w phoenix avondale/goodyear area
if you come up to phx we could probably work something out
06-04-2009, 01:34 AM
#13
12 Second Club
Thread Starter
iTrader: (10)
Join Date: Nov 2007
Location: Tucson, AZ
Posts: 1,095
Likes: 0
Received 0 Likes
on
0 Posts
Its ok I did the rears and the passenger today, I will do the drivers tomorrow and the require should be finished.
Oh well anything worth doing is worth doing right I guess.
After that its Dynaspark and Ported IM time as well as a few other clean up items.
Then wax and prep for the show Sat.
Oh well anything worth doing is worth doing right I guess.
After that its Dynaspark and Ported IM time as well as a few other clean up items.
Then wax and prep for the show Sat.
06-04-2009, 10:37 PM
#15
12 Second Club
Thread Starter
iTrader: (10)
Join Date: Nov 2007
Location: Tucson, AZ
Posts: 1,095
Likes: 0
Received 0 Likes
on
0 Posts
I have been putting on my new ported Intake Manifold. Everything is wired up except I have not run the Amp Pos line yet.
The battery was dead so I am putting in my Optima in the morning. (Had to charge the battery in it so it could go in my MX6 when I remove the Optima)
The battery was dead so I am putting in my Optima in the morning. (Had to charge the battery in it so it could go in my MX6 when I remove the Optima)
