how amazing would this tips look mounted on a camaro?!?!
12-20-2007, 06:16 AM
#1
TECH Fanatic
Thread Starter
iTrader: (12)
Join Date: Sep 2005
Location: South Burbs of Chicago
Posts: 1,593
Likes: 0
Received 0 Likes
on
0 Posts
how amazing would this tips look mounted on a camaro?!?! hey guys, (sorry for grammer, its 6 am and i havnt gone to bed yet,lol)
i was just checking out exhaust parts, and i came across this corvette system, how awesome would these tips look mounted upside down (molding to the bumper) of a camaro.
http://cgi.ebay.com/ebaymotors/SLP-P...ayphotohosting
i was just checking out exhaust parts, and i came across this corvette system, how awesome would these tips look mounted upside down (molding to the bumper) of a camaro.
http://cgi.ebay.com/ebaymotors/SLP-P...ayphotohosting
Last edited by Camaro Ryder KV; 12-20-2007 at 06:32 AM.
Trending Topics
12-20-2007, 02:17 PM
#9
TECH Fanatic
iTrader: (39)
Join Date: Mar 2005
Location: Central Cal - Merced County
Posts: 1,513
Likes: 0
Received 0 Likes
on
0 Posts
I don't think the curvature of the CME valance follows the tips very well. The tips seems to be wider than the opening but anything is possible. Since the tips are cast aluminum they may be altered by cutting them in the middle and bringing them closer together to fit in the opening a little better. The valance would still need to be modified to look correct.
12-20-2007, 03:54 PM
#11
TECH Veteran
iTrader: (7)
Join Date: Jun 2006
Location: Bay Area California
Posts: 4,409
Likes: 0
Received 0 Likes
on
0 Posts
on a CME valence they would look completely out of place, and without a valence they look like complete *** (trust me, I have seen it done before). So without a custom valence, its a bad idea
12-21-2007, 07:52 AM
#12
TECH Fanatic
iTrader: (10)
Join Date: Aug 2002
Location: Danville,PA
Posts: 1,110
Likes: 0
Received 0 Likes
on
0 Posts
The thing is in the photoshopped pic, I think the proportions may be off. Those tips probably aren't that big. They may actually be the width of the the CME opening.
12-21-2007, 09:00 AM
#13
TECH Enthusiast
iTrader: (1)
Join Date: Jun 2006
Location: Staten Island, New York
Posts: 606
Likes: 0
Received 0 Likes
on
0 Posts
He's right. Even if they fit in the cme, the two outside edges would have alot of extra room where the tips go to a point. So yea, the cme would need to be modded some how. It has potential but would prob require alot of work.
12-22-2007, 05:17 PM
#18
TECH Enthusiast
Join Date: Aug 2007
Posts: 685
Likes: 0
Received 0 Likes
on
0 Posts
you guys know its not going to be that wide
its for the c5 vette
also having the curve on top would give the bottom a more straight factory look like on the c5 below
use the licence plate above as a reference point
its for the c5 vette
also having the curve on top would give the bottom a more straight factory look like on the c5 below
use the licence plate above as a reference point
Last edited by Rai; 12-22-2007 at 05:31 PM.
12-22-2007, 05:28 PM
#19
TECH Enthusiast
Join Date: Aug 2007
Posts: 685
Likes: 0
Received 0 Likes
on
0 Posts
http://vettetube.com/view_video.php?...45dfe4146c5660
http://www.youtube.com/watch?v=GKvbn...eature=related
video on c5 at idle
with a custom cme valence and the middle painted black .. i think they would look pretty good
http://www.youtube.com/watch?v=GKvbn...eature=related
video on c5 at idle
with a custom cme valence and the middle painted black .. i think they would look pretty good
Last edited by Rai; 12-22-2007 at 07:28 PM.