$2600 to rebuilt my a4 transmission
11-06-2006, 03:03 PM
#1
Teching In
Thread Starter
iTrader: (6)
Join Date: Nov 2003
Location: Georgia
Posts: 39
Likes: 0
Received 0 Likes
on
0 Posts
$2600 to rebuilt my a4 transmission Guys my 02 trans am has 65,000 miles and my 3rd and 4th gears are basically gone or so the dealer the car aint shifting @ all. All its doing is reving up to 7000 rpm, But damn there charging me $2600 is this about right or should I just get a tranny from like Finish Line Performance?
11-06-2006, 03:07 PM
#2
go get a built one. you can get one for around 3000k and itll be a bad *** trans. look at the sponsors and check um out there. it also depends on what you will be doing with the car. if you beat on it and wanna mod it more than go with a built one. screw the stock trans it sucks
11-06-2006, 03:09 PM
#3
For $2600 you could get a better than stock rebuild. I would look at getting a highly built tranny. I am going to go through mine with the help of a friend that does it for a living. I have all Alto Red Eagle clutches including the Z pack that increases the number of 3/4 clutches, beast sunshell, .490 boost valve, 13 vane pump kit, and more. I hope that when I am done that it will last a whole season of 10 sec passes.
You are getting boinked in the butt!! I got my fully built trans from rock-on for $2200 shipped! Go with them, or FLT, or performabuilt... 
11-06-2006, 04:29 PM
#7
performabuilt has a stage 2 (able to handle 700hp), and a 3500 stall verter for a good price. it was on their site for a little over $2K i think (dont remember the exact price and i cant check cause im at work). im getting that setup and paid a good price (ls1tech discount and military discount)
Trending Topics
11-06-2006, 06:19 PM
#8
4L60E LSX LS1 Type used from 1998 up WITH
ENGINES with out converter ----------$1600.00-----------------
with 1800 to 2000 stall---------$1675.00---------
with 2300 to 2500 stall---------$1835.00---------
with 9.5 inch 3000 stall ------$2075---------
with 9.5 inch 3500 stall------$2100-------------
Go to website to see deatils
ENGINES with out converter ----------$1600.00-----------------
with 1800 to 2000 stall---------$1675.00---------
with 2300 to 2500 stall---------$1835.00---------
with 9.5 inch 3000 stall ------$2075---------
with 9.5 inch 3500 stall------$2100-------------
Go to website to see deatils
__________________
11-06-2006, 06:58 PM
#10
Teching In
Thread Starter
iTrader: (6)
Join Date: Nov 2003
Location: Georgia
Posts: 39
Likes: 0
Received 0 Likes
on
0 Posts
Ok I found a place thats gonna charge me $1200 so Ill be doing that. And first thing monday morning I'm putting the car for sale or Im going to trade it in to get an 03-04 Cobra so Ill be going 2 the dark side LOL . GMMG and QTP headers will be for sale.Thanks for everything guys.
11-06-2006, 08:28 PM
#11
TECH Addict
iTrader: (3)
Join Date: Nov 2005
Location: Lincoln, NE
Posts: 2,869
Likes: 0
Received 0 Likes
on
0 Posts
A stock rebuild is just that, extremely expensive and possibly short-lived insurance until it goes out again.
I would do it right the first time, and let it handle what you throw at it later.
I would do it right the first time, and let it handle what you throw at it later.
11-06-2006, 08:40 PM
#12
You are getting raped.
I pulled mine out, got it fully built for $1,200 & im in California.
Also it has 12 month warranty and its rated at 600hp
Shop around, ive seen TH400 go for less then what your paying bro.
I pulled mine out, got it fully built for $1,200 & im in California.
Also it has 12 month warranty and its rated at 600hp
Shop around, ive seen TH400 go for less then what your paying bro.
