LSX In 91 C4 Corvette My Swap
06-30-2015, 03:42 AM
#226
Teching In
Join Date: May 2006
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
hello LSCha0s
i wish that i read your thread befor i started my project, i went thru all same drama's
maybe the different between us, that i bought complete wiring harness from Mr.Jody @ VetteAid, and it's custom build, which cost me around $1700 but he did really a great job, i just have to figure out where some few wires need to go, but that not a big issue ,
my corvette is 1984, own it from long long time, never drive it or start it since 2008 i guess.
i start my project 4 months ago, and because i'm not from States, it's take long time to wait for parts, i turned the engine today for first time, and it's sound great.
right now i'm done with the engine and all drive-line, will try to finish the wiring Puzzle's,assemble the interior and re-install the AC parts .
my swap is LS1 with 4L60E, i used GM performance parts Complete Accessory Drive System Without A/C, and then bought high AC bracket, i dropped and remove the engine almost 8 times, but now everything set and clear .
i got the engine and transmission for free from friend, but the other parts cost me more than $14000, most of the amount for shipping .
i did restore most of life parts of the car + new Radio and sound system, few interior parts, suspension and bushing, fuel system + the swap .
here is few photos of the build, didn't really take many photos .
https://goo.gl/photos/Lh1h8UtW77VYGiyC6
hopefully finish my project in next 1 month .
i wish that i read your thread befor i started my project, i went thru all same drama's
maybe the different between us, that i bought complete wiring harness from Mr.Jody @ VetteAid, and it's custom build, which cost me around $1700 but he did really a great job, i just have to figure out where some few wires need to go, but that not a big issue ,
my corvette is 1984, own it from long long time, never drive it or start it since 2008 i guess.
i start my project 4 months ago, and because i'm not from States, it's take long time to wait for parts, i turned the engine today for first time, and it's sound great.
right now i'm done with the engine and all drive-line, will try to finish the wiring Puzzle's,assemble the interior and re-install the AC parts .
my swap is LS1 with 4L60E, i used GM performance parts Complete Accessory Drive System Without A/C, and then bought high AC bracket, i dropped and remove the engine almost 8 times, but now everything set and clear .
i got the engine and transmission for free from friend, but the other parts cost me more than $14000, most of the amount for shipping .
i did restore most of life parts of the car + new Radio and sound system, few interior parts, suspension and bushing, fuel system + the swap .
here is few photos of the build, didn't really take many photos .
https://goo.gl/photos/Lh1h8UtW77VYGiyC6
hopefully finish my project in next 1 month .
Last edited by Red Z28; 06-30-2015 at 03:50 AM.
03-07-2016, 10:22 AM
#228
Teching In
Join Date: Feb 2015
Location: Calgary,Ab
Posts: 5
Likes: 0
Received 0 Likes
on
0 Posts
sending unit machining i am doing a similar swap on an 86 over i have a thread on CF this would really help me out
cheers
03-07-2016, 10:39 AM
#229
Teching In
Join Date: May 2006
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
this page really helped me in my swap, i think your qustion answer there ..
http://tech.corvettecentral.com/2010...-c4-corvettes/
