charchri4

iTrader: (11)

Miata LS1 conversion process start to finish video.

bbksicvic

Hello everyone I got a problem if anyone could help. I did a 5.3 Drive By Wire swap in a 1964 Chevy truck. The truck don't start when I have the TAC MODULE Box plugged in. When TAC is plugged in the fuel pump relay chatters and wont start. But when I unplug the TAC MODULE it starts right up. QUESTION when I first put it in it all worked fine then just quit out of no where. Do the TAC MODULES quit out of nowhere

chevySS425

Hello everyone I got a problem if anyone could help I'm building a 1950 chevy pickup truck with 2006 5.3 engine plan to install 2008 intake manifold drive by cable throttle and 4l60e trans. I have 2000 Silverado wire harness with the red and blue computer drive by cable also. somebody have schematics for this application any help be appreciated thank you.

Root2812

iTrader: (1)

I also have a 1950 Chevy Truck I'm putting a 2000 5.3 into. Check out LT1swap.com he has the pinouts all listed for the harness.

charchri4

iTrader: (11)

Guys ^^ the best 70 bucks I ever spent on my build was to buy the factory shop manuals for my donor car off ebay. Granted 3/4s of the F body books is useless for a Miata but the rest is priceless!

chevySS425

Thank you for the help.

chevySS425

Thank you for the Help you have any pick of your truck? look like you building a nice ride

Root2812

iTrader: (1)

Yes. Here is a link to my thread. I'm not very far along yet. I just started on the suspension. Engine comes next.
https://ls1tech.com/forums/conversio...x-w-5-3-a.html

chevySS425

Im finish with the chassis and I use mustang II front suspension what you going to use?

Root2812

iTrader: (1)

Lets move our chat over to my build thread so we don't clutter the swap guides sticky with unrelated posts.

But I did use a Fatman Fabrications Mustang II IFS.

DAGeorgie

yes please. or at least some DIY stand alone wire harness mods on gen III LS1 cause that's what most kids are using these days. or any info on 240sx/LSX swaps would be nice. shameless plug...silviav8dotcom is a good site too.

JDub66

iTrader: (1)

Did you find some other good impala B body threads? Just curious. Found one good one so far...

68imp

would you mind letting me know what website you have found! gonna start on a 68 and that would be helpfull

78T/a

anyone have a list for 2nd gen f-body

charchri4

iTrader: (11)

Go hang out with these guys

http://www.pro-touring.com/forums/75-The-LSX-Forum

http://www.lateral-g.net/forums/forumdisplay.php4?f=70

Tpgates2627

Try dirty dingo motorsports.

PhenomJay

iTrader: (1)

Probably done to death but more 240sx LS1 swap guide stuff.

http://my.prostreetonline.com/2013/0...-into-a-240sx/

Brandon Shiver

Anyone got any advice on a 2002 ls1 / 4l60e swap into a 1973 Impala. What headers, motor mounts and accessory brackets to use? Any suggestions are greatly appreciated.

Brandon

biggs1978

Hey forum I'm new to this but this far I like this. I am thinking about doing a engine swap to my 2004 Lincoln ls v8 with the ls1. The Lincoln ls has the jaguar engine and the two engines look identical. To me when I look at both they look exactly the same. Just the valve covers are shaped different. What I would like to know is would the ls1 fit into the body of the Lincoln ls? I know I would have to modify the motor mounts. As far as transmission and pcm and other electric components would I have a lot to take on?

biggs1978

Can you swap out the factor Lincoln ls 3.9 motor and transmission with the ls1 motor and trans? They both look identical, and would I have to swap the pcm out of the Lincoln or rewire a ls1 pcm?