enzo354

iTrader: (2)

Well, doing a fun little build in the 86.

The car



Well I got rid of the mystery motor.



And picked up this grand old beast




A good amount of nasty smelling crap under the intake.




What the hell happened here?



Needs a good old hone and she will be back up. After I order a few more parts of course..... A few.



Now I have a few questions as I start this.


As I sit now, I got the ms3 cam with 114 LSA. The motor has the 862 heads on it, and I got a set of the trick flow dual spring valve springs. My question is, with this set up will I need any fly cutting? Also what would you suggest I do pushrod wise?

the_merv

iTrader: (88)

I would do Chromeoly Pushrods. Clay it if you aren't sure.'

Just FYI..them Knock Sensors are supposed to come out before the Valley Cover comes off..

enzo354

iTrader: (2)

Alright, I'll check into it, and I cant get those sensors out for the life of me. 1/2 of the bolts on this motor are wither seized in or so rusty you cant use a wrench on them.

the_merv

iTrader: (88)

From the looks of it the Grommets pulled out of the Valley Cover.

Since you have it out try Channel Locks and twist them out.. It's not like you are trying to save them..

enzo354

iTrader: (2)

I'll give it a try. I just don't want them to crunch in and then not move.

the_merv

iTrader: (88)

You'll get them with Channel Locks.. I've done it with the Valley Cover on..

enzo354

iTrader: (2)

Haha sounds like it should be easy then. Beautiful Monte you have there btw!

the_merv

iTrader: (88)

Thanks.

Yours looks like its still factory paint, it's in good shape.

enzo354

iTrader: (2)

It's a "Night Time" looking paint. In the day you can see all of the swirls and haze and chips and dings, but cruising at night I'm not afraid to rod the **** out of it. *I live on gravel so this is a big statement haha*

Now I need to figure out if I want to go with a fuel tank from a v6 monte, or a fuel cell.

the_merv

iTrader: (88)

Same with mine.. Get up close and you see the small stuff. It's a driver.

IT_SS

iTrader: (5)

nice!

enzo354

iTrader: (2)

Thanks, now here is kind of a dumb question, I'm new to all of this wiring though haha.

When I install this motor, can I get by with just the ecm and the wiring to the motor and trans, or do I also need to pick up the under hood fuse box from a 5.3 truck? I've seen it done both ways.

t72ss402

iTrader: (10)

No questions are dumb. most people do not use them, but you can if you want to. Its is alot easier to set your harness up as a 4 wire hook up and just an after market fuse block and a couple of relays. here is some good info for you

http://www.lt1swap.com/wiringharness.htm

http://www.youtube.com/results?searc....0.xgD2taCON2U

These guys on this board are great for getting info from. So ask your questions.

Tim.

enzo354

iTrader: (2)

Thank you very much, that site has a ton of info. I'm going to try not to use it so that I can clean up the engine bay a decent amount.

enzo354

iTrader: (2)

Well the ms3 I picked up, with the 114lsa I was reading could be bad for my build. I'm going to sell it to my buddy with his gto and stick to a stock cam for now. I need the money to go into other parts anyway.

MillsMotorvation

Any cam over stock is better than none. These engines love cams! Take advantage of those stock 15degree heads! I have a Z06 cam in mine, and it gave the car aprox400hp. See if you can get a cam. Jegs has the Z06 cam on sale for like $270 I think. Good luck!

IT_SS

iTrader: (5)

I'm thinking about leaving my 5.3 stock expecpt for bolts and intake & seeing what I can get with e85 & tuning

tta656

iTrader: (5)

awesome info

speedfreak90

man i hope the motor i get doesnt look like that... good luck with your build!

enzo354

iTrader: (2)

Brought home the motor from the machine shop, he never touched it so I went and got it....

Also, who sells a flexplate/ spacer to mate the 5.3 to a 4l80e? I have the tranny from a 1996 and Ive been searching but getting a run around.