Another LSx S-10 headr option
#1
TECH Enthusiast
Thread Starter
iTrader: (15)
Join Date: Jun 2005
Posts: 609
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Hey all. Sent off a message to a mod here to make sure this was OK. If for any reason something is posted that is concerning to a mod, please let me know.
To all S-10 LSx swap guys. I am working with American Racin Headers to build my long tubes for my 98' 2 wheel drive S-10. I am trying to drum up some interest to see if they are worth putting into production.
What I have is a 1998 2 wheel drive S-10. It will be recieving an LQ-4 this summer with a T-56. This truck will be lowered with a ZQ-8 suspension and will be running at least a 255 tire up front.
The goal is to make a tue long tube with a minimum 1 3/4 primary tube and a 3" collector. The biggest stipulation is that the headers have to be made to exit inside the frame (not in the wheel wells), be high enough not to hit the ground on a lowered truck (unless you are on air bags, then it's your issue if it hits), clear the A/C box, and have room to change spark plugs. They will have a ture 1 3/4 primary. Not just bumped up at the flange and then be really a 1 5/8 again.
These headers will be made using my truck as a test truck. It will be late summer before these are even ready to view. But, if I can get interest and even buyers lined up (at least 10-15), they will make them a production header for any to buy. The projected cost could be in the range of $1200. That being said, buy a set of quality headers for a Vette, F-Body, GTO or other high performance car. You will pay similar pricing. I am paying much more than that for the one off set. And will be pushing to get them into production if there is enough interest.
Please keep in mind. My truck will have the engine in the foward posistion using the typical 2.8 mounts with engine plates like the ebay ones. I will also be using the LH-8 oil pan. I will not say these will fit a 4 wheel drive. I am certain they will not.
At this moment, ARH and I are still in the planning phase. And They are not tied into building me anything. I did this this permission from them and a moderator here. If all works out, we will have a great header for people looking for quality, fitment (if using the same parts and placing the engine in the same place), and performance over the other options we have.
PM me if there is more info needed.
Thanks.
To all S-10 LSx swap guys. I am working with American Racin Headers to build my long tubes for my 98' 2 wheel drive S-10. I am trying to drum up some interest to see if they are worth putting into production.
What I have is a 1998 2 wheel drive S-10. It will be recieving an LQ-4 this summer with a T-56. This truck will be lowered with a ZQ-8 suspension and will be running at least a 255 tire up front.
The goal is to make a tue long tube with a minimum 1 3/4 primary tube and a 3" collector. The biggest stipulation is that the headers have to be made to exit inside the frame (not in the wheel wells), be high enough not to hit the ground on a lowered truck (unless you are on air bags, then it's your issue if it hits), clear the A/C box, and have room to change spark plugs. They will have a ture 1 3/4 primary. Not just bumped up at the flange and then be really a 1 5/8 again.
These headers will be made using my truck as a test truck. It will be late summer before these are even ready to view. But, if I can get interest and even buyers lined up (at least 10-15), they will make them a production header for any to buy. The projected cost could be in the range of $1200. That being said, buy a set of quality headers for a Vette, F-Body, GTO or other high performance car. You will pay similar pricing. I am paying much more than that for the one off set. And will be pushing to get them into production if there is enough interest.
Please keep in mind. My truck will have the engine in the foward posistion using the typical 2.8 mounts with engine plates like the ebay ones. I will also be using the LH-8 oil pan. I will not say these will fit a 4 wheel drive. I am certain they will not.
At this moment, ARH and I are still in the planning phase. And They are not tied into building me anything. I did this this permission from them and a moderator here. If all works out, we will have a great header for people looking for quality, fitment (if using the same parts and placing the engine in the same place), and performance over the other options we have.
PM me if there is more info needed.
Thanks.
#2
TECH Enthusiast
Thread Starter
iTrader: (15)
Join Date: Jun 2005
Posts: 609
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I have gotten aa few PM's in regards to some of the things I posted up. I can see the confusion as I babbled on a bit. So below is the info needed.
These headers WILL be a 304 stainless steel.
They will be made to work with they typical EBAY type engine mounting brakets and stadard 2.8 rubber engine mounts.
The headers WILL NOT exit outside the frame and be in the wheel wells at all. So running a large tire with say a 9.5 rim will not be an issue as far as the headers are concered.
The production units are slated to be a 1 3/4. Options to have a 1 3/4 steped to a 1 7/8 is possible but not set in stone.
Again, these are for trucks that are 2 wheel drive and are using an LH-8 pan. Or something similar in width to that pan. I cannot promise they will fit any other pan.
These headers WILL be a 304 stainless steel.
They will be made to work with they typical EBAY type engine mounting brakets and stadard 2.8 rubber engine mounts.
The headers WILL NOT exit outside the frame and be in the wheel wells at all. So running a large tire with say a 9.5 rim will not be an issue as far as the headers are concered.
The production units are slated to be a 1 3/4. Options to have a 1 3/4 steped to a 1 7/8 is possible but not set in stone.
Again, these are for trucks that are 2 wheel drive and are using an LH-8 pan. Or something similar in width to that pan. I cannot promise they will fit any other pan.
#3
Launching!
iTrader: (10)
Join Date: Oct 2008
Location: Winnipeg Manitoba Canada
Posts: 293
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
why not try to kill 2 birds with 1 stone and make them fit both 2 wheel drive and 4x4 applications. If your going to invest time/money, I would try get the most return possible. It might open up to alot more sales. Just my .02 cents on it.
#5
TECH Enthusiast
Thread Starter
iTrader: (15)
Join Date: Jun 2005
Posts: 609
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I also am not building a 4x4 truck. And I cannot invest the extra cash into a 4x4 and a 2wd (I want the 2wd and have a 2wd truck in the works now). I would believe that the trucks would need a much differant system no mater what you could do.
Maybe in the future when I can afford to build a 4x4, I might try and make a kit that works. But for now, I have to leave that up to someone else.
#6
TECH Enthusiast
iTrader: (10)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Post this at s10forum.com. A sponsor over there did somewhere between 15 and 20 sets of 1 3/4 LTs in two runs and I think they were over $1000 each...IN MILD STEEL! I would buy a set when I get done with my swap. I'm in the middle of swapping my LS1(LS6 heads/intake mild cam) and fully built 4l60 into a 1996 RCSB. I already bought the sanderson POS coated headers but would have loved to drop the coin on a set of ARHs as I have a set in my SSS and love them.
Trending Topics
#8
TECH Enthusiast
iTrader: (9)
Join Date: Mar 2008
Location: IL
Posts: 698
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I beleive CPW made a couple batches of the headers and either didn't have the space or time or whatever. Now the design has been sold to RetroLSX and the price was reportedly like $2k for a set of stainless LT's ![Sad](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_sad.gif)
Shame there isn't alot of companies making these for S10s, it's a pretty popular swap and after I'm done with my car, I may do my daily driver
![Sad](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_sad.gif)
Shame there isn't alot of companies making these for S10s, it's a pretty popular swap and after I'm done with my car, I may do my daily driver
![Grin](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_grin.gif)
#9
TECH Enthusiast
Thread Starter
iTrader: (15)
Join Date: Jun 2005
Posts: 609
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Post this at s10forum.com. A sponsor over there did somewhere between 15 and 20 sets of 1 3/4 LTs in two runs and I think they were over $1000 each...IN MILD STEEL! I would buy a set when I get done with my swap. I'm in the middle of swapping my LS1(LS6 heads/intake mild cam) and fully built 4l60 into a 1996 RCSB. I already bought the sanderson POS coated headers but would have loved to drop the coin on a set of ARHs as I have a set in my SSS and love them.
These will fit any LS engine. All but the LSx raised engine block types. But the 4.8, 5.3 (aluminum and iron blocks), 6.0 (LQ-4 and LQ-9), LS-1, 2, 3, 6 and other production GM LS engines.
I beleive CPW made a couple batches of the headers and either didn't have the space or time or whatever. Now the design has been sold to RetroLSX and the price was reportedly like $2k for a set of stainless LT's ![Sad](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_sad.gif)
Shame there isn't alot of companies making these for S10s, it's a pretty popular swap and after I'm done with my car, I may do my daily driver![Grin](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_grin.gif)
![Sad](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_sad.gif)
Shame there isn't alot of companies making these for S10s, it's a pretty popular swap and after I'm done with my car, I may do my daily driver
![Grin](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_grin.gif)
I am hoping to keep pricing down. It was estimated that a set of uncoated long tubes in 304 stainless will go for $1200. I would like to see it lower, but the low numbers being produced is keeping the cost over $1k.
#12
Staging Lane
iTrader: (4)
Join Date: Mar 2008
Location: south houston
Posts: 60
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I would buy a set but I just bought some CPW LT headers.
I hope this works out. There are Alot of guys looking for LT, just got to get his info out to everyone! Also it is nice there going to be made out of stainless!
I hope this works out. There are Alot of guys looking for LT, just got to get his info out to everyone! Also it is nice there going to be made out of stainless!
#15
On The Tree
iTrader: (2)
Join Date: Jun 2007
Location: Ft. Worth Tx.
Posts: 104
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
i will be looking for some headers soon for my s-10 that im swapping a 5.3l in, but my s-10 is bagged and lays frame so i will have to see if they make them fit above the frame rail.
#17
TECH Enthusiast
Thread Starter
iTrader: (15)
Join Date: Jun 2005
Posts: 609
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Looking to try and keep them above the frame rails. It all depends on how the primaries fit when merged with the collector. I would like my whole exhaust including the headers to tuck above the lowest point in the frame for both looks and safty of the exhaust. We will see when the system is built.
#19
On The Tree
iTrader: (2)
Join Date: Jun 2007
Location: Ft. Worth Tx.
Posts: 104
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
heres the link to his post over there http://www.s10forum.com/forum/f213/f...-tubes-465942/