408ci,L92 heads with Cary's carb intake #'s Been meaning to post this for a while:devil: Just a mild little street car setup :nod: -408ci 6.0L block setup -FMS stage 2 L92 heads -FMS custom hyd cam :secret2: -Yella Terra rockers -Morel HI-RPM tie bar lifters -11.4 CR -Perf Induction L92 carb intake ! -Accufab 4500 T\B -ARH 1-7\8" to 2" stepped headers -FMS 3-1\2" custom y-pipe -Rossler TH400 -Yank Elim 3600 converter -Strange 12-bolt w\3.73 gears -Strange Chromemoly driveshaft -'98 PCM w\SD tuning Dyno runs were done through exhaust, 275\60-15 M\T drag radials,factory water pump and full acc belt on and with 93 pump gas ! Cam is under 240 on the intake and idles SWEET at 850 RPM ! http://www.futralmotorsports.com/ima...s/DSC01748.jpg http://www.futralmotorsports.com/ima...Intakedyno.jpg |
wow! nice numbers through that drivetrain! |
High RPM power!!! |
sorry if this is a completely stupid question, but are those numbers on an engine dyno?? What was the lift on the cam? reason I ask is those are pretty wicked numbers for an auto, small cam (for a 408) and 3:73s if those are whp. did you guys do the shortblock? |
Nice power! Sweet intake, beautiful welds! |
again, futral does it again! that is a chasis dyno, so the numbers are at the rear wheels. |
has it been down the track yet? |
Originally Posted by gator's 99TA
(Post 11936996)
that is a chasis dyno, so the numbers are at the rear wheels. futral, we exchanged pm's a few months ago, you guys never got back to me on an iron 5.3 shortblock to a 346 with a forged bottom. |
Sweet power. That is well over 600 rwhp with a manual transmission. |
Originally Posted by Spectre86
(Post 11936781)
sorry if this is a completely stupid question, but are those numbers on an engine dyno?? What was the lift on the cam? reason I ask is those are pretty wicked numbers for an auto, small cam (for a 408) and 3:73s if those are whp. did you guys do the shortblock? |
Originally Posted by Spectre86
(Post 11937166)
wow. kick ass setup. futral, we exchanged pm's a few months ago, you guys never got back to me on an iron 5.3 shortblock to a 346 with a forged bottom. |
Originally Posted by Futral
(Post 11937400)
Sorry about that, I may have cleared it out by accident....Please e-mail to finish up the conversation,since I don't log on very often. |
|
email sent. |
Nicely done Alan! DAMN! I still need an intake that will fit under a 2 inch raised vette hood. This isn't it. |
Holy wow awesome setup, Numbers and work thats low 10s car fo sure. 7500rpm too. |
best my car made with a similiar combo was 475 or so RWHP. That is very impressive intake Cary. Nice work Allan! |
Originally Posted by WizeAss
(Post 11941035)
best my car made with a similiar combo was 475 or so RWHP. That is very impressive intake Cary. Nice work Allan! |
Badass. Would a 4500 TB and that intake fit under a 4" Camaro cowl hood? |
my engine setup right now is close to yours, the old setup was -408ci 6.0L block setup -TSP cnc L92 heads -TR LS1 head cam -Yella Terra rockers -11.9 CR -gm L92 carb intake -edelbrock choker elbow -kooks 1-7\8" headers -kooks 3" to 2.5" slip fit into 3" catback -T56 -spec stage 3+ clutch -7.5" 10 bolt w\3.73 gears -'98 PCM w\SD tuning made 503rwhp now i am using a different cam morell tie bars stock l76 gonna get a good setup before i dyno it again I am impressed with your setup, its the highest hp 408 LS3 car ive seen yet |
All times are GMT -5. The time now is 06:23 AM. |
© 2024 MH Sub I, LLC dba Internet Brands