What will my 430" make in my C5Z... ??
#1
TECH Enthusiast
Thread Starter
iTrader: (7)
Join Date: May 2010
Location: Sacramento
Posts: 537
Likes: 0
Received 0 Likes
on
0 Posts
What will my 430" make in my C5Z... ??
-430" (4"x4.135")
-PRC 265 LS7's (385cfm @ .600") @ dcr 11.75:1... scr @ 8.31:1... quench @ .041"
-243/259 ~.620" 113.5+4
-Kooks 1 7/8 x 3" .. no cats
-MSD Intake (light port/cleaned) w/ NW 102 w/ Vararam
-Morel .750" wheel, hi-rpm link lifters
-Manton 3/8" .095" wall pushrods
Hoping to get ok timing out of it... I would hope for 18-21*... have to deal with this California 91 octane.
Let the guesstimates flow...
-PRC 265 LS7's (385cfm @ .600") @ dcr 11.75:1... scr @ 8.31:1... quench @ .041"
-243/259 ~.620" 113.5+4
-Kooks 1 7/8 x 3" .. no cats
-MSD Intake (light port/cleaned) w/ NW 102 w/ Vararam
-Morel .750" wheel, hi-rpm link lifters
-Manton 3/8" .095" wall pushrods
Hoping to get ok timing out of it... I would hope for 18-21*... have to deal with this California 91 octane.
Let the guesstimates flow...
#2
Teching In
iTrader: (2)
Join Date: Oct 2008
Location: Toronto, Canada
Posts: 6
Likes: 0
Received 0 Likes
on
0 Posts
Hi Scott
568 RHP, and 525 RWT.....What rockers you using ? can you use Ls3 rockers with those Ls7 small bore PRC heads? or had to LS7 rockers only?
I am going with similar 429 cid, 4"X4.130, in fact just got the short block from machine shop, but going with stock LS3 top end due to no budget left...lol, but eventually go with Ls7 top end sometime later...man our cams are very similer...243/255 111+3 Cam on HUC lobes.....-3cc wiseco pistons, callies rods, callies crank......pfadt 1 7/8 no cats........johnson SLa lifters....so on.
I think i sold 3.4" Aand A pulley to you couple yrs ago on CF?....
note: SC kit is sold, going NA stroker this time.
568 RHP, and 525 RWT.....What rockers you using ? can you use Ls3 rockers with those Ls7 small bore PRC heads? or had to LS7 rockers only?
I am going with similar 429 cid, 4"X4.130, in fact just got the short block from machine shop, but going with stock LS3 top end due to no budget left...lol, but eventually go with Ls7 top end sometime later...man our cams are very similer...243/255 111+3 Cam on HUC lobes.....-3cc wiseco pistons, callies rods, callies crank......pfadt 1 7/8 no cats........johnson SLa lifters....so on.
I think i sold 3.4" Aand A pulley to you couple yrs ago on CF?....
note: SC kit is sold, going NA stroker this time.
#3
TECH Addict
iTrader: (22)
Join Date: Sep 2004
Location: tennessee
Posts: 2,639
Likes: 0
Received 0 Likes
on
0 Posts
with 8.3 dcr you may be able to get your timing up there where it needs to be and still not knock. some combos around where your setup is are over 600rw so no reason to think yours shouldn't either unless they stay conservative. i'll say 590-600 rwhp with 515-520 rwtq. maybe if it knocks you can always throw in some octane booster or hook up meth.
#4
TECH Enthusiast
Thread Starter
iTrader: (7)
Join Date: May 2010
Location: Sacramento
Posts: 537
Likes: 0
Received 0 Likes
on
0 Posts
Sami.. long time. You also sold me your livernois 243's, awesome heads... those are long gone, as is my blower combo.. lol
Here we are, big cubes, heads and cam... I think I'll like it the best. I was really hoping to touch 600 with it, we'll see.
Rockers are LS7's with the Schaub bushing kit.
Here we are, big cubes, heads and cam... I think I'll like it the best. I was really hoping to touch 600 with it, we'll see.
Rockers are LS7's with the Schaub bushing kit.
#5
TECH Enthusiast
Thread Starter
iTrader: (7)
Join Date: May 2010
Location: Sacramento
Posts: 537
Likes: 0
Received 0 Likes
on
0 Posts
with 8.3 dcr you may be able to get your timing up there where it needs to be and still not knock. some combos around where your setup is are over 600rw so no reason to think yours shouldn't either unless they stay conservative. i'll say 590-600 rwhp with 515-520 rwtq. maybe if it knocks you can always throw in some octane booster or hook up meth.