TSP Stage 1 heads, Torquer 2 Dyno #'s
#1
Staging Lane
Thread Starter
iTrader: (1)
Join Date: Jun 2006
Location: Nashua, NH
Posts: 99
Likes: 0
Received 0 Likes
on
0 Posts
TSP Stage 1 heads, Torquer 2 Dyno #'s
TSP Stage 1 heads, Torquer 2 cam 114 , LS6 intake, UD Pulley, LG Street headers, Stock TB, Vararam, Z06 TI exhaust, 3.42 gears, Vig 3200 stall, 100 octane fuel. 396 RWHP, 340 Torque. What do you all think? Car is an A4 Built tranny. Wheels are 19" with 295/30R19s BFG KDWS
Trending Topics
#8
Staging Lane
Thread Starter
iTrader: (1)
Join Date: Jun 2006
Location: Nashua, NH
Posts: 99
Likes: 0
Received 0 Likes
on
0 Posts
Should I buy the fast 90 intake and t/b?. Would it make enough of a difference to spend the big money. Why was my torque low?. Is there anything else I can add to get in the 430-440 range?. Car pulls hard and was tuned nicely by Slowhawk. Idles great.
#9
10 Second Club
iTrader: (14)
I would only do the FAST 90mm if you're willing to spend the extra money to have it ported. You're right, the TQ does seem kind of low... but I think an unlocked verter will give you skewed #'s. Overall, it sounds like it's a nice set up that drives well on the street.
#11
10 Second Club
iTrader: (14)
Originally Posted by WS6FirebirdTA00
Why? HOSS and I both gained 15 rwhp with unported intakes. Definately worth the money on one.
#12
TECH Addict
Originally Posted by 86 IROC
At peak, what about under the curve? 15 is very good, I don't see people typially get that much. A friend of mine w/ an AFR 205 head - 224/228 cam combo only got 9 from an unported 90 & a 90mm TB over his stock stuff. It is an A4 C5 w/ a stall & full bolt ons.
The 90/90 will show most gains from 5500rpm and above, so if the stock shift point and rpm limter are in place I wouldn't expect much gain.
And from the dyno results I've seen the 90/90 should match a LS6 100% if not a little better all the way from 2000rpm up, right until it starts making more.
#13
10 Second Club
iTrader: (14)
Originally Posted by 300bhp/ton
How high was it being revved?
The 90/90 will show most gains from 5500rpm and above, so if the stock shift point and rpm limter are in place I wouldn't expect much gain.
And from the dyno results I've seen the 90/90 should match a LS6 100% if not a little better all the way from 2000rpm up, right until it starts making more.
The 90/90 will show most gains from 5500rpm and above, so if the stock shift point and rpm limter are in place I wouldn't expect much gain.
And from the dyno results I've seen the 90/90 should match a LS6 100% if not a little better all the way from 2000rpm up, right until it starts making more.
#14
Staging Lane
Thread Starter
iTrader: (1)
Join Date: Jun 2006
Location: Nashua, NH
Posts: 99
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by 300bhp/ton
How high was it being revved?
The 90/90 will show most gains from 5500rpm and above, so if the stock shift point and rpm limter are in place I wouldn't expect much gain.
And from the dyno results I've seen the 90/90 should match a LS6 100% if not a little better all the way from 2000rpm up, right until it starts making more.
The 90/90 will show most gains from 5500rpm and above, so if the stock shift point and rpm limter are in place I wouldn't expect much gain.
And from the dyno results I've seen the 90/90 should match a LS6 100% if not a little better all the way from 2000rpm up, right until it starts making more.
#16
I just had a new 2001 Vette crate motor installed along with a set of PRC LS6 stage 1 heads. I am also running the Torquer V2 cam but on a 112. My car put down 386 rwhp thru an A4 unlocked with a Vig 3200-3400 stall. So I would say your rite about where you ought to be. The guy tuning said bring mine back in 1500 miles after the motor breaks in a little bit and he thought he could get 400 rwhp out of it. I've got the LS6 intake and a Dynamaxx long tube with the catted Y. Runs like a scalded dog doesn't it!!
Last edited by dedge; 09-25-2006 at 10:47 AM. Reason: addition
#18
Staging Lane
Thread Starter
iTrader: (1)
Join Date: Jun 2006
Location: Nashua, NH
Posts: 99
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by dedge
I just had a new 2001 Vette crate motor installed along with a set of PRC LS6 stage 1 heads. I am also running the Torquer V2 cam but on a 112. My car put down 386 rwhp thru an A4 unlocked with a Vig 3200-3400 stall. So I would say your rite about where you ought to be. The guy tuning said bring mine back in 1500 miles after the motor breaks in a little bit and he thought he could get 400 rwhp out of it. I've got the LS6 intake and a Dynamaxx long tube with the catted Y. Runs like a scalded dog doesn't it!!
#19
LS1Tech Premium Sponsor
iTrader: (3)
Then would you care to explain this a4 locked graph here:
Same heads & completely different torque. PRC heads ship with cnc ports & a cnc valve job to insure consistant results with every set!
Same heads & completely different torque. PRC heads ship with cnc ports & a cnc valve job to insure consistant results with every set!
Originally Posted by Brian Tooley
Most times a low torque # is from the heads, what is the port volume on those you have?
#20
Originally Posted by Trevor @ Texas Speed & Perf.
Then would you care to explain this a4 locked graph here:
Same heads & completely different torque. PRC heads ship with cnc ports & a cnc valve job to insure consistant results with every set!
Same heads & completely different torque. PRC heads ship with cnc ports & a cnc valve job to insure consistant results with every set!