LS1TECH - Camaro and Firebird Forum Discussion

LS1TECH - Camaro and Firebird Forum Discussion (https://ls1tech.com/forums/)
-   General Maintenance & Repairs (https://ls1tech.com/forums/general-maintenance-repairs-102/)
-   -   my camaro won't start (https://ls1tech.com/forums/general-maintenance-repairs/1152287-my-camaro-wont-start.html)

MOZART9T Jul 23, 2009 09:25 AM

my camaro won't start
 
hi

I'm having a problem with my 2002 camaro

my problem is that I have to turn the key for 1-2 min untill it start

this happen most of the time and I just have to wait until it turn on

I changed the ignition switch, check the battery but the problem isn't going

what do you think it might be the problem :(

fleetmgr Jul 23, 2009 11:15 AM

Have you checked your fuel pressure? Have you changed your fuel filter recently?

Dewey Jul 23, 2009 11:22 AM

more info please, will it just turn over for a minute and then start, or does it not make contact and do nothing? does the starter sound strained? details, chief... details. where do you live by the way.

Ice78Transam Jul 23, 2009 11:23 AM

sounds like a fuel problem if it starts...after a while. But much more detail please.

MOZART9T Jul 23, 2009 02:12 PM

while the key is turn on ,it does nothing for 1-2 min then start suddenlly

nothing happen when I turn the key on, only the gages turn off, which mean there is a contact

I didn't check fuel pressure nor changed fuel filter

I'll have to check it tomorrow


sorry but I'm not so good in English , I'm from Saudi Arabia

fleetmgr Jul 23, 2009 02:47 PM

No problem, we'll get it worked out. :)

When you say with the key on, it won't start for 1-2 minutes. Is this with the engine cranking, or only the key on?

99monguse Jul 23, 2009 03:41 PM

Did you try the ignition relay by chance? Try swapping one of the fan relays into the ignition relay.

Dewey Jul 23, 2009 11:50 PM

i think i know what is happening. try this, it may be as simple as the starter fuse in the cabin fuse box is bad. just take out the fuse labeled something like stater 2 or ignition. take that fuse out altogether and turn the key. if that works then you need to replace the ignition relay. it'll either be a ten amp or a three amp fuse.
this happened to me at work one night. the truck would kill the gauges and stereo, then do nothing as if it were turning over. all i did was pull out the ignition fuses, and the truck just started. you will hear some strange noises, all you have to do is put the fuses back in to make the beeps stop.

MOZART9T Jul 27, 2009 07:02 AM


Originally Posted by fleetmgr (Post 11953752)
No problem, we'll get it worked out. :)

When you say with the key on, it won't start for 1-2 minutes. Is this with the engine cranking, or only the key on?

the engine won't crank, the lights in the panel will just go off and I have to hold the key in the "on" position for couple of minutes until it crank and start

I tried removing the starter fuse and tried to turn it on but nothing happened, and the lights didn't even go off

MOZART9T Jul 27, 2009 07:10 AM


Originally Posted by 99monguse (Post 11954036)
Did you try the ignition relay by chance? Try swapping one of the fan relays into the ignition relay.

I replaced the relay with a new one and that didn't work either

robinpugs06 Jul 27, 2009 12:17 PM

fuel pressure regulator?

LS6427 Jul 27, 2009 12:50 PM

1-2 minutes....damn thats a long time to crank that starter. You're gonna be buying a new starter if you keep doing that.

Did this start "all of a sudden"...or has it been slowly building up to this over time.


.

MOZART9T Jul 28, 2009 03:12 AM

Note: the engine will not crank for whole time "1-2 min.", I just hold the key at the "on position" and nothing happens for "1-2 min.", and after that the engine starts to crank and it would start right away

I hope I made it clear this time :)

Dewey Jul 28, 2009 09:27 AM

Yes. That is much clearer, thank you. It sounds to me like the lock cylinder in the ignition mechanism is not making contact. When you replaced the atarter switch, what was replaced? What I mean is did you replace only the starter switch or the lock and ignition cylinders at the same time? When you get a chance try this: either try to turn the key very slowly in the ignition or try to move the key around in the cylinder if that doesn't work.

MOZART9T Jul 29, 2009 10:12 AM

This is the part I changed the last time,

http://www.eye4rugs.com/images/ignition/700754.jpg


and this is a clip for the problem I took today

http://www.youtube.com/watch?v=dJcuBm0UFMk

MOZART9T Jul 31, 2009 04:25 AM

up .....

Dewey Aug 1, 2009 01:14 AM

after watching the video several times... i'm stumped. i've never seen a car do that before. the only suggestion that i can make is to get a new key cut from the VIN number of your car (or the key code engraved onto the ignition cylinder in the picture above) - an oem rounded key, not like the one you have now.

LS6427 Aug 1, 2009 01:25 AM


Originally Posted by MOZART9T (Post 11985191)
This is the part I changed the last time,

http://www.eye4rugs.com/images/ignition/700754.jpg


and this is a clip for the problem I took today

http://www.youtube.com/watch?v=dJcuBm0UFMk

That would make for a shitty get-a-way car. :lol:

Get yourself a new key, the resistor in the key could be wacked.


.

rabbit320 Aug 25, 2009 01:44 PM

any new news from this? i think i am having same problem...

Norway Aug 26, 2009 10:37 AM

im having the same problem too, it occurs completely at random for me


All times are GMT -5. The time now is 10:23 AM.


© 2026 MH Sub I, LLC dba Internet Brands