LS1TECH - Camaro and Firebird Forum Discussion

LS1TECH - Camaro and Firebird Forum Discussion (https://ls1tech.com/forums/)
-   Generation III External Engine (https://ls1tech.com/forums/generation-iii-external-engine-6/)
-   -   Flowmaster Delta 40's Anyone Run Them???? (https://ls1tech.com/forums/generation-iii-external-engine/731288-flowmaster-delta-40s-anyone-run-them.html)

Sweet71 Jun 13, 2007 12:52 PM

Flowmaster Delta 40's Anyone Run Them????
 
I was thinkin about gettin some 3" Flowmaster delta 40 mufflers for my car and i was wondering if anyone runs these and could tell me how they sound or if they have a sound clip of them? Thanks Guys?

Sweet71 Jun 13, 2007 03:26 PM

Nobody??

HavATampa Jun 13, 2007 10:02 PM

Are they the same as the Super 40's? If so, I'm installing a pair right now. Don't know how they sound yet, but should be deep.

BriancWS6 Jun 13, 2007 10:06 PM

Well, the 40 series 2 chamber flows are pretty large. It would be difficult to install a pair of those into a setup. I know that one can be done easily though. How is yours going to be setup?

Sweet71 Jun 14, 2007 01:44 AM

dual 3 inch through an x pipe, the delta flow ones are a little bit smaller only 4 inches thick instead of 5

BriancWS6 Jun 14, 2007 04:29 PM


Originally Posted by Sweet71
dual 3 inch through an x pipe, the delta flow ones are a little bit smaller only 4 inches thick instead of 5

The single chamber (10 series) flows I run, are about as tight as I would want to squeeze under there unless you want to do some major re-construction of the floorboards. The case is 4in thick, 6.250 long, 9.750 wide, and overall length is 10.250.

The ones your getting are huge in comparison, 5x13x10, and 19in overall. I dont think you'll be able to tuck them under the car :(
http://store.summitracing.com/partde...5&autoview=sku

HavATampa Jun 14, 2007 09:05 PM

I'm welding up a pair of Super 40's endcap to endcap under the gas tank. Duals coming over each side of the axle and exits on each side of the bumper. It's been a real challenge to get them to fit though, but it's coming along. You're right, these Super 40's are freaking huge. :jest:



Originally Posted by BriancWS6
Well, the 40 series 2 chamber flows are pretty large. It would be difficult to install a pair of those into a setup. I know that one can be done easily though. How is yours going to be setup?


Sweet71 Jun 16, 2007 11:02 AM

Just finished installing my delta 40's and they sound awesome! will get a sound clip soon, everything is good, hang low but it is to be expected

HavATampa Jun 16, 2007 10:14 PM

Where are they mounted? Post some pics.

GeArBaNgEr56 Jun 17, 2007 10:24 AM

Pics!

Sweet71 Jun 17, 2007 03:33 PM

The car is on a hill in the pics, it looks alot lower than it is, i have driven about 400 miles and its bottemed out only twice and it was because i wasnt paying attention.

http://i129.photobucket.com/albums/p.../camaro158.jpg

http://i129.photobucket.com/albums/p.../camaro159.jpg

http://i129.photobucket.com/albums/p.../camaro160.jpg

Sweet71 Jun 17, 2007 03:33 PM

http://i129.photobucket.com/albums/p.../camaro161.jpg

Sorry the pics suck i was in a hurry

HavATampa Jun 17, 2007 04:33 PM

Holy crap, that's low. You guys must have some smooth roads in the north. I'd rip them off in a day down here in the bayou. :)

Sweet71 Jun 17, 2007 04:44 PM

hahah no its not too bad, theres lots of pot holes but just gotta be carefull


All times are GMT -5. The time now is 11:13 PM.


© 2026 MH Sub I, LLC dba Internet Brands