Generation III Internal Engine 1997-2006 LS1 | LS6
Sponsored by:
Sponsored by:

5.3 question

Thread Tools
 
Search this Thread
 
Old 09-23-2009, 08:06 PM
  #1  
TECH Regular
Thread Starter
iTrader: (33)
 
ksk1980's Avatar
 
Join Date: May 2005
Location: Gretna, VA
Posts: 464
Likes: 0
Received 0 Likes on 0 Posts

Arrow 5.3 question

i tried a search and couldnt find what i was looking for . anyhow what kinda #'s could be accomplished w/ a 5.3 botton end stg2 5.3 heads and a MS3 cam w/ a ls6 intake , LT's 6spd/4.10's
Old 09-24-2009, 01:09 AM
  #2  
On The Tree
iTrader: (7)
 
pdbq's Avatar
 
Join Date: Sep 2008
Location: Lakeland, FL
Posts: 155
Likes: 0
Received 0 Likes on 0 Posts
Default

I've heard that 5.3s make about 30-40 rwhp less than LS1s with the same cams, heads, exhausts, compression ratio, etc. Free bump as I'd also like to confirm this...
Old 09-24-2009, 09:49 AM
  #3  
11 Second Club
iTrader: (20)
 
5_02ls1's Avatar
 
Join Date: Oct 2006
Location: Virginia
Posts: 3,131
Likes: 0
Received 0 Likes on 0 Posts

Default

look over on performance trucks....i have a mild h/c 5.3 in my car...never had it on a dyno though....ms3 is a lot of cam for the 5.3 id look into some arp or katech rod bolts...

the above comment on 30-40 rwhp less is not true...more like 20-25 if that.....ive seen cam only trucks with tiny cams 220s or less put 350 to the tire...theres a thread somewhere with a 5.3 in a trans am with headers and an ls6 cam that made 327rwhp....just search around
Old 09-24-2009, 02:20 PM
  #4  
TECH Resident
iTrader: (3)
 
ramdaspadhye's Avatar
 
Join Date: May 2005
Posts: 889
Likes: 0
Received 1 Like on 1 Post
Default

Don't run anything of a 224 cam in a 5.3...
Old 09-24-2009, 03:43 PM
  #5  
12 Second Club
iTrader: (91)
 
MUSTANGBRKR02's Avatar
 
Join Date: Aug 2006
Location: Maine
Posts: 4,599
Likes: 0
Received 5 Likes on 4 Posts

Default

I agree MS3 is to big for that engine. Bigger isn't always better.
Old 09-24-2009, 04:02 PM
  #6  
TECH Senior Member
iTrader: (127)
 
NemeSS's Avatar
 
Join Date: Sep 2005
Location: Houston,TX
Posts: 6,886
Received 7 Likes on 7 Posts

Default

Originally Posted by ksk1980
i tried a search and couldnt find what i was looking for . anyhow what kinda #'s could be accomplished w/ a 5.3 botton end stg2 5.3 heads and a MS3 cam w/ a ls6 intake , LT's 6spd/4.10's
make for a response motor
i would keep cam under 220 duration for throttle response and drivabilty
i would recommend the LPE GT11 cam, that is a very responsive cam in a 5.3 and will be evn better with the available heads and intake.
Old 09-24-2009, 08:24 PM
  #7  
TECH Regular
Thread Starter
iTrader: (33)
 
ksk1980's Avatar
 
Join Date: May 2005
Location: Gretna, VA
Posts: 464
Likes: 0
Received 0 Likes on 0 Posts

Default

only reason i asked is i have the ms3 out of my LS1 that snapped a rod bolt. i have found tons of 5.3's for cheap where i lived and was thinking about swaping it into the TA just to get it back on the road . and had already planned on new rod main bearings and Katech rod bolts while i was right there anyways. i just want a cheap motor to spray a 175 shot on because it not a DD. if it last for awhile of street driving and a couple of sprays thats good enough for me.




All times are GMT -5. The time now is 12:18 AM.